Category : Tutorials + Patches
Archive   : GAMEPORT.ZIP
Filename : GAMEPORT.INF

 
Output of file : GAMEPORT.INF contained in archive : GAMEPORT.ZIP

From: [email protected] (Bill Frolik)
Newsgroups: comp.sys.ibm.pc
Subject: Re: How to read game port
Date: 6 Apr 90 17:47:16 GMT

> 1) Is there anyone that can tell me the specifications for the game port
> connector?

15-pin D-shell connector:

PIN SIGNAL PIN SIGNAL
--- ------ --- ------
1 +5V 8 +5V
2 button 1 9 +5V
3 stick 1 10 button 3
4 GND 11 stick 3
5 GND 12 GND
6 stick 2 13 stick 4
7 button 2 14 button 4
15 +5V

Game card has a female connector;
Joystick cable has male connector.
Joystick wiring:

+5 ________________
|
stick1 ________ |
| 100K |
_/\/\/\_____|
stick2 ________ |
| 100K |
_/\/\/\_____|
stick3 ________ |
| 100K |
_/\/\/\_____|
stick4 ________ |
| 100K |
_/\/\/\_____|
___
button1 ______o o_______
___ |
button2 ______o o_______|
___ |
button3 ______o o_______|
___ |
button4 ______o o_______|
|
GND ________________|


> 2) As near as I can figure, I have to use the inpw() function (I'm using
> C) to read the ports. Unfortunately, I don't know the port number to
> give the function to read the port. If this isn't the right/best way,
> please let me know.

You need to do byte I/O to and from port 201h.
To read the joysticks (or your slide pot positions), you
must first write a byte to port 201h. It doesn't matter
what value you send, as long as you perform an I/O write.
This triggers the 558 timer on the game adapter.

Game port 201h byte:
_______________________________________________________
| 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
| but4 | but3 | but2 | but1 | stk4 | stk3 | stk2 | stk1 |
|______|______|______|______|______|______|______|______|

The most machine-independent way to sample the game port
is to use a timer. Note the time (e.g., read the countdown
register in Timer 0, you need pretty fine resolution and this
timer performs 65535 counts every 55 ms) just before you
trigger the 558. After triggering, sit in a loop reading
port 201h and examining bits 0-3. For those bits that have
a joystick pot attached, you'll see them sit for a while at 0,
then become 1. As each bit flips back to 1, note the time
again. When all bit 0-3 have flipped back to 1, you're almost
done. Compute elapsed time for each bit, and you end up with
a value that is proportional to pot position.

If you're lazy and don't care about machine independence,
you can just trigger the card, then sit in a loop and count
up from zero. As each bit flips back to 1, save the count
for that bit. I've seen a few games that probably use
this method. Problem is that if you then run the same code
on a faster/slower machine, your calibration can get very
easily messed up.

Buttons can be read at any time just by reading port 201h
and looking at bits 4-7. No triggering is required.
Button bits are normally 1; while a button is depressed,
its bit will flip to 0.

___________________________________________

Bill Frolik Hewlett-Packard Co.
hp-pcd!bill Corvallis, Oregon
[email protected] (503)750-4082


  3 Responses to “Category : Tutorials + Patches
Archive   : GAMEPORT.ZIP
Filename : GAMEPORT.INF

  1. Very nice! Thank you for this wonderful archive. I wonder why I found it only now. Long live the BBS file archives!

  2. This is so awesome! 😀 I’d be cool if you could download an entire archive of this at once, though.

  3. But one thing that puzzles me is the “mtswslnkmcjklsdlsbdmMICROSOFT” string. There is an article about it here. It is definitely worth a read: http://www.os2museum.com/wp/mtswslnk/