Category : Music and Digitized Voice
Archive   : MODOBJ-1.ZIP
Filename : HARDWARE.DOC

 
Output of file : HARDWARE.DOC contained in archive : MODOBJ-1.ZIP
MODOBJ ********* (C) Mark J Cox
MODOBJ ** 1991-2
MODOBJ *******
MODOBJ **************

Hardware devices for great sound output!


I. CONTENTS
ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ

How to make:
Mono output from a parallel port for about 5 pounds
Mono output from a parallel port for around 1 pound
Stereo from one parallel port for about 12 pounds
A +5v power supply
A 22W amplifier

This document has been supplied with MODOBJ. You may distribute
this file freely with any program you include MODOBJ in as long as
it remains unaltered.


I. INTRODUCTION
ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ

MODPLAY will play modules through the PC Speaker as mentioned above, via
an D to A converter on any of the three possible parallel ports, in stereo
if you have an D to A converter on both LPT1 and LPT2 (this sounds really
good) and also through a special board that plays stereo from one
printer port ("stereoÄonÄ1")

1. HOW TO MAKE A D/A CONVERTER FOR FIVE POUNDS
ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ

A simple circuit for HiFi quality sound needs only a few components (and
this circuit will work with other software). It even sounds better than
a Sound Blaster for sampled output!

You need:

IC1 a ZN426E (about 3 pounds) (Ferranti or Plessey are UK manufacturers)

C1 a 10micro-farad electrolytic capacitor (10V or greater)

C2 a 4.7micro-farad electrolytic capacitor (10V or greater)

R1 a 380ohm resistor (5%, 1/8W)

CON1 a phono socket for connecting a lead to your amplifier

CON2 a 25 way male D-type connector for your parrallel port

A bit of 10 way cable - or 10 short wires.

A +5v supply


Zn426e +5V
D-type pin no \ ÚÄÄÄÄÄÄÄÄ¿ ³
(2) D0 ÄÄÄ´9 14ÃÄÄ´
(3) D1 ÄÄÄ´10 ³ ÚÁ¿
(4) D2 ÄÄÄ´11 ³ ³ ³ 390ê
(5) D3 ÄÄÄ´12 ³ ÀÂÙ
(6) D4 ÄÄÄ´13 5ÃÄÄ´
(7) D5 ÄÄÄ´1 6ÃÄÄ´ +
(8) D6 ÄÄÄ´2 4ÃÄijÄÄÄÄÄÄÄÄ´ÛÄÄÄÄ> TO AMPLIFIER
(9) D7 ÄÄÄ´3 7 ³ ³ 10æF
ÀÄÄÄÄÂÄÄÄÙ +Ï (may not be needed)
³ 4.7æFÛ
³ ³
(25) GND ÄÄÄÄÄÄÄÄÁÄÄÄÄÄÄÁÄÄÄÄÄÄÄÄÄÄÄÄÄÄ GND


2. USING A DIFFERENT DAC
ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ

Lots of people have found that they cannot get the ZN* chips outside
the UK - so heres a circuit that will do the same as above..
Use a DAC0800 or DAC0801 or DAC0803 from National Semiconductors...

DAC 080x
Parallel Port Pin ÚÄÄÄÄÄÄÄÄ¿0.01æF 0.1æF
(2) D0 ÄÄÄ´12 16ÃÄÄ´ÛÄÄÄÄ´ÛÄÄÄÄÄÄÂÄÄÄ GND
(3) D1 ÄÄÄ´11 ³ ³
(4) D2 ÄÄÄ´10 15ÃÄÄÄÄÄÄÄÄÄÛÛÛÛÛÛÄÙ5kê
(5) D3 ÄÄÄ´9 ³
(6) D4 ÄÄÄ´8 14ÃÄÄÄÄÄÄÄÄÄÛÛÛÛÛÛÄ¿5kê
(7) D5 ÄÄÄ´7 13ÃÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´
(8) D6 ÄÄÄ´6 2ÃÄÄ´ÛÄÄÄÄÄÄÄÄÄÄÄÄÁÄÄ +5V
(9) D7 ÄÄÄ´5 3 1 4ÃÄÄÄÄÄÄÄÄÄÄ´ÛÄÄÄÄ> TO AMPLIFIER
ÀÄÄÂÄÂÄÄÄÙ0.1æF + 10æF
ÀÄ´ (may not be needed)
³
(25) GND ÄÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ GND

The 0.01uF and 2x 0.1uF capacitors are Ceramic. Resistor values
not critical


2. GETTING A +5V POWER SUPPLY
ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ

Catalogues such as MAPLIN (uk) provide simple circuits for obtaining
a +5v power supply (it only has to be 100mA maximum). Alternatively
you could tap +5v off the keyboard connector or use 3 1.5volt
batteries (or even 4 1.5volt batteries with two diodes in series to
drop the voltage). In fact, anything that produces a voltage in the
range 4.5 Ä 5.5 volts. (in fact you can even tap +5v from the game
port). Don't forget to connect the 0v of your power supply to the GND
rail shown.

Heres a simple circuit for +5v from mains. Mains voltage is lethal
so always get a qualified person to make this if you are unsure. Make
certain that the mains voltage is completely isolated from the computer
side and that it is impossible to touch - If you don't want to take the
risk then don't make this circuit.

ÚÄÄÄÄÄÄÄÄÄÄÄ¿ ÷ÚÄÄÄ¿+ ÚÄÄÄÄÄÄ¿
³ ³ ³ B ÃÄÄÄÄÄÂÄÄÄÄÄÄÄÂÄÄÄÄÄ´ 7805 ÃÄÄÄÄÂÄÄÄÄÄÄ +5V
ÄÄÄÄÄÄÄ´Step down ÃÄÄÄÄÄÄ´ R ³ ³+ ³ ÀÄÄÂÄÄÄÙ ³+
Mains ³transformer³ 6V ³ I ³ ÍØÍ C1 ÍØÍ C2 ³ ÍØÍ C3
³to 6VAC ³ AC ³ D ³ ³ ³ ³ ³
ÄÄÄÄÄÄÄ´ ÃÄÄÄÄÄÄ´ G ³ ³ ³ ³ ³
³ ³ ³ E ÃÄÄÄÄÄÁÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÄÁÄÄÄÄÄÄ 0V
ÀÄÄÄÄÄÄÄÄÄÄÄÙ ÷ÀÄÄÄÙ-

C1 1000 æF electrolytic capacitor (Circuit from Kenneth
C2 0.1 æF ceramic capactitor Aaron, Israel)
C3 100 æF electrolytic capacitor
BRIDGE any diode bridge


3. HOW TO MAKE AN EVEN CHEAPER D/A
ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ

For the price of 20 1% resistors and a plug, with no power supply
needed you can make a D/A converter that sounds close to the IC
one above (it seems only the UK can get a Plessey ZN426E)

You need one plug for your amp, one for your parallel port and
9 20k and 9 10K resistors
Use 1% resistors if possible Ä and 20k sound much better than 22k

Printer Port:

signal pin 20k 20k
D0 2 >ÄÄÄ°°°ÄÂÄ°°°ÄÄ0v
20k ° 10k
D1 3 >ÄÄÄ°°°Ä´
20k ° 10k
D2 4 >ÄÄÄ°°°Ä´
20k ° 10k
D3 5 >ÄÄÄ°°°Ä´
20k ° 10k
D4 6 >ÄÄÄ°°°Ä´
20k ° 10k
D5 7 >ÄÄÄ°°°Ä´
20k ° 10k
D6 8 >ÄÄÄ°°°Ä´
20k ° 10k
D7 9 >ÄÄÄ°°°Ä´
20k ° 10k 100nF
ÃÄÄÄÄÄÄ´ÛÄÄÄÄ> TO AMPLIFIER
° 10k
GND 20 >ÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄ>
0v

Thanks to Harry Stox for the above circuit. Again, make sure all
the 0v lines are connected together. The 100nF capacitor may not
be needed, try removing it if this circuit sounds poor.



4. STEREO-ON-1 BOARD
ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ

It is possible to play in stereo with only one parallel port (MODPLAY
version 2.00 onwards) using the circuit below. MODPLAY will
automatically detect this circuit if it is present and work out what
address it is at Ä so you can plug it into any of your parallel ports.
MODPLAY needs no further options and will default to playing through
this device. The +5v supply can be anywhere between 4.5 and 5.5 volts
so it could be run from three 1.5v batteries. (Or from four
rechargable batteries as these are only 1.2v)

* Stereo-on-1 works from MODPLAY 2.03 onwards where it did not in 2.00 *

You can use your stereo-on-1 board with other programs that require
a single D/A on the port as follows:

Find out what address your port is at (LPT1 = 0378, LPT2 = 0278) and
add 2 (LPT1 = 037A, LPT2 = 027A). Go into DEBUG and type
o 37a,3 (replacing 37a with the port address)
q
Then all sound directed to the parallel port will come out of both
channels.

ZN428
ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿ 390ê
ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´11 6ÃÄÂÄÄÄÄÂı±±±±ÄÄ+5v
³ ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´12 7ÃÄÙ ³
³ ³ ÚÄÄÄÄÄÄÄÄÄÄÄÄÄ´13 3ÃNC ³
³ ³ ³ ÚÄÄÄÄÄÄÄÄÄÄÄ´14 ³ ³ + 10æF
³ ³ ³ ³ ÚÄÄÄÄÄÄÄÄÄ´15 5ÃÄÄÄÄÄijÄÄĶÃÄÄÄÄÄ> Left out
³ ³ ³ ³ ³ ÚÄÄÄÄÄÄÄ´16 ³ ³ 0vÄÄÄ>
20 >Ä0v ³ ³ ³ ³ ³ ³ ÚÄÄÄÄÄ´1 10ÃÄÄ+5v ³
³ ³ ³ ³ ³ ³ ³ ÚÄÄÄ´2 9ÃÄÂÄ0v ³
14 >ÄÄÄijijijijijijijijÄÄÄ´4 8ÃÄÙ ³
³ ³ ³ ³ ³ ³ ³ ³ ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ ³
11 >ÄÄÄÄ´ ³ ³ ³ ³ ³ ³ ³ ZN428 ³ + 1æF
³ ³ ³ ³ ³ ³ ³ ³ ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿ ÃÄÄĶÃÄ0v
9 >ÄÄÄÄÁijijijijijijijÄÄÄ´11 D7 VRIN 6ÃÄÄÄÄÄÄÙ
8 >ÄÄÄÄÄÄÁijijijijijijÄÄÄ´12 D6 VROUT 7à NC
7 >ÄÄÄÄÄÄÄÄÁijijijijijÄÄÄ´13 D5 NC 3à NC
6 >ÄÄÄÄÄÄÄÄÄÄÁijijijijÄÄÄ´14 D4 ³ + 10æF
5 >ÄÄÄÄÄÄÄÄÄÄÄÄÁijijijÄÄÄ´15 D3 OUT 5ÃÄÄÄÄÄÄÄÄĶÃÄÄÄÄÄ> Right out
4 >ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÁijijÄÄÄ´16 D2 ³ 0vÄÄÄ>
3 >ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÁijÄÄÄ´1 D1 +V 10ÃÄÄ+5v
2 >ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÁÄÄÄ´2 D0 0v 9ÃÄÂ0v
1 >ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´4 !EN 0v 8ÃÄÙ
25 pin male D connector ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ


Notes:

Make sure all the 0v lines are connected together and connected to the
0v line of your power source. Also, make sure the +5v lines are
connected together. The lines marked 'NC' do not need to be connected.

If a ZN428 is not available, any D/A with input latches will work -
the D/A should latch the data bus when pin 4 (!EN) is low.

Ä³Ä = No connection, ÄÅÄ = joined

The above circuit (Stereo-on-1) is (C) Mark J Cox 1991, 29 Lundie Close
Stenson Fields, Derby DE2 3AN; and is supplied for personal use only.
For any other use, please contact the author at the address above. If
this circuit is abstracted or incorporated into any other document or
circuit then that document or documentation supplied with that circuit
must contain this paragraph of text. Any commercial use where not
agreed by written contract with the author (Mark J Cox) is prohibited.


13. STEREO AMPLIFIER
ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ

For those of you who have built a stereo DAC and haven't enough
inputs to your Amplifier - Kenneth Aaron has supplied this
circuit which is designed to give a high power (11W per channel)
high quality, low interference, single rail supply amplifier!

Enable
>ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÄ¿ ÚÄÄÄÄÂÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ +12v
³+ ³ ³ ³
ÍØÍ 10æFÚÄÁÄÄÄÁÄÄÄÄÁÄÄÄÄÄ¿
0v ÄÄÄÄÄÄÙ ³ 7 13 3 1ÃÄÄÄÄÄÄÄÄÄÄÄÄ Left
Left 470nF ÚÄÄ´4 2ÃÄÄÄÄÄÄÄÄÄÄÄÄ Speaker
>ÄÄÄÄÄÄÄÄÄ×ÄÄÄÄÄÄÄÄ´ ³ ³
ÀÄÄ´5 TDA 7370 14ÃÄÄÄÄÄÄÄÄÄÄÄÄ Right
Right 470nF ÚÄÄ´11 15ÃÄÄÄÄÄÄÄÄÄÄÄÄ Speaker
>ÄÄÄÄÄÄÄÄÄ×ÄÄÄÄÄÄÄÄ´ ³ ³
ÀÄÄ´12 ³
+ÚÄÄÄÄÄ´6 8 9 10ÃÄNC
47æF ÍØÍ ÀÄÄÄÄÄÂÄÄÄÂÄÄÄÄÄÄÙ
³ ³ ³
ÀÄÄÄÄÄÄÄÄÄÄÄÁÄÄÄÁÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ 0v

Make sure that 0v of the +12v supply is connected to all the 0v
connections on the main circuit. The enable line has to be tied
to +12v to 'switch on' the amp


14. AUTHOR
ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ

Mark J Cox Electronic Mail:
29 Lundie Close [email protected]
Stenson Fields
Derby, UK If that fails - try:
DE2 3AN [email protected]




  3 Responses to “Category : Music and Digitized Voice
Archive   : MODOBJ-1.ZIP
Filename : HARDWARE.DOC

  1. Very nice! Thank you for this wonderful archive. I wonder why I found it only now. Long live the BBS file archives!

  2. This is so awesome! 😀 I’d be cool if you could download an entire archive of this at once, though.

  3. But one thing that puzzles me is the “mtswslnkmcjklsdlsbdmMICROSOFT” string. There is an article about it here. It is definitely worth a read: http://www.os2museum.com/wp/mtswslnk/