Category : Miscellaneous Language Source Code
Archive   : 1216REF.ZIP
Filename : CHAPTER.004

 
Output of file : CHAPTER.004 contained in archive : 1216REF.ZIP

** Programmer's Technical Reference for MSDOS and the IBM PC **
ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿
³ Shareware Version, 12/16/88 ³
³ Please Register Your Copy ³
ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ
Copyright (c) 1988 Dave Williams


C H A P T E R F O U R

DOS INTERRUPTS AND FUNCTION CALLS



DOS REGISTERSÃÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ

DOS uses the following registers, pointers, and flags when it executes
interrupts and function calls:
ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿
³GENERAL REGISTERS ³ register ³ definition ³
³ ÃÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´
³ ³ AX ³ accumulator (16 bit) ³
³ ³ AH ³ accumulator high-order byte (8 bit) ³
³ ³ AL ³ accumulator low order byte (8 bit) ³
³ ³ BX ³ base (16 bit) ³
³ ³ BH ³ base high-order byte (8 bit) ³
³ ³ BL ³ base low-order byte (8 bit) ³
³ ³ CX ³ count (16 bit) ³
³ ³ CH ³ count high order byte (8 bit) ³
³ ³ CL ³ count low order byte (8 bit) ³
³ ³ DX ³ data (16 bit) ³
³ ³ DH ³ date high order byte (8 bit) ³
³ ³ DL ³ data low order byte (8 bit) ³
ÃÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´
³SEGMENT REGISTERS ³ register ³ definition ³
³ ÃÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´
³ ³ CS ³ code segment (16 bit) ³
³ ³ DS ³ data segment (16 bit) ³
³ ³ SS ³ stack segment (16 bit) ³
³ ³ ES ³ extra segment (16 bit) ³
ÃÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´
³INDEX REGISTERS ³ register ³ definition ³
³ ÃÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´
³ ³ DI ³ destination index (16 bit) ³
³ ³ SI ³ stack index (16 bit) ³
ÃÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´
³SEGMENT REGISTERS ³ register ³ definition ³
³ ÃÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´
³ ³ CS ³ code segment (16 bit) ³
³ ³ DS ³ data segment (16 bit) ³
³ ³ SS ³ stack segment (16 bit) ³
³ ³ ES ³ extra segment (16 bit) ³
ÃÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´
³INDEX REGISTERS ³ register ³ definition ³
³ ÃÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´
³ ³ DI ³ destination index (16 bit) ³
³ ³ SI ³ stack index (16 bit) ³
ÃÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´
³POINTERS ³ register ³ definition ³
³ ÃÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´
³ ³ SP ³ stack pointer (16 bit) ³
³ ³ BP ³ base pointer (16 bit) ³
³ ³ IP ³ instruction pointer (16 bit) ³
ÃÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´
³FLAGS AF, CF, DF, IF, OF, PF, SF, TF, ZF ³
ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ

These registers, pointers, and flags are "lowest common denominator" 8088-8086
CPU oriented. DOS makes no attempt to use any of the special or enhanced
instructions availible on the later CPUs which will execute 8088 code, such as
the 80186, 80286, 80386, or NEV V20, V30, V40, or V50.

When DOS takes control after a function call, it switches to an internal
stack. Registers which are not used to return information (other than AX) are
preserved. The calling program's stack must be large enough to accomodate the
interrupt system - at least 128 bytes in addition to other interrupts.
DOS actually maintains three stacks -
stack 1: 384 bytes (in DOS 3.1)
for functions 00h and for 0Dh and up, and for ints 25h and 26h.

stack 2: 384 bytes (in DOS 3.1)
for function calls 01h through 0Ch.

stack 3: 48 bytes (in DOS 3.1)
for functions 0Dh and above. This stack is the initial stack used by
the int 21h handler before it decides which of the other two to use.
It is also used by function 59h (get extended error), and 01h to 0Ch if
they are called during an int 24h (critical error) handler. Functions
33h (get/set break flag), 50h (set process ID), 51h (get process ID)
and 62h (get PSP address) do not use any DOS stack under DOS 3.x
(under 2.x, 50h and 51h use stack number 2).

IBM and Microsoft made a change back in DOS 3.0 or 3.1 to reduce the size of
DOS. They reduced the space allocated for scratch areas when interrupts are
being processed. The default seems to vary with the DOS version and the
machine, but 8 stack frames seems to ring a bell. That means that if you get
more than 8 interrupts at the same time, clock, disk, printer spooler,
keyboard, com port, etc., the system will crash. It seems to happen usually on
a network. STACKS=16,256 means allow 16 interrupts to interrupt each other and
allow 256 bytes for each for scratch area. Eight is marginal.

DOS 3.2 does some different stack switching than previous versions. The
interrupts which are switched are 02h, 08h, 09h, 0Ah, 0Bh, 0Ch, 0Dh, 0Eh, 70h,
72h, 73h, 74h, 75h, 76h, and 77h. DOS 3.2 has a special check in the
initialization code for a PCjr and don't enable stack switching on that machine.



INTERRUPTSÃÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ

Microsoft recommends that a program wishing to examine or set the contents of
any interrupt vector use the DOS function calls 35h and 25h provided for those
purposes and avoid referencing the interrupt vector locations directly.
DOS reserves interrupt numbers 20h to 3Fh for its own use. This means absolute
memory locations 80h to 0FFh are reserved by DOS. The defined interrupts are as
follows with all values in hexadecimal.


ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿
³Interrupt 21h Function Call Request ³
ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ
(0:0084h)
DOS provides a wide variety of function calls for character device I/O, file
management, memory management, date and time functions,execution of other
programs, and more. They are grouped as follows:

call description
00h program terminate
01h-0Ch character device I/O, CP/M compatibility format
0Dh-24h file management, CP/M compatibility format
25h-26h nondevice functions, CP/M compatibility format
27h-29h file management, CP/M compatibility format
2Ah-2Eh nondevice functions, CP/M compatibility format
2Fh-38h extended functions
39h-3Bh directory group
3Ch-46h extended file management
47h directory group
48h-4Bh extended memory management
54h-57h extended functions
5Eh-5Fh networking
60h-62h extended functions
63h-66h enhanced foreign language support


List of DOS services: * = undocumented
00h terminate program
01h get keyboard input
02h display character to STDIO
03h get character from STDAUX
04h output character to STDAUX
05h output character to STDPRN
06h direct console I/O - keyboard to screen
07h get char from std I/O without echo
08h get char from std I/O without echo, checks for ^C
09h display a string to STDOUT
0Ah buffered keyboard input
0Bh check STDIN status
0Ch clear keyboard buffer and invoke keyboard function
0Dh flush all disk buffers
0Eh select disk
0Fh open file with File Control Block
10h close file opened with File Control Block
11h search for first matching file entry
12h search for next matching file entry
13h delete file specified by File Control Block
14h sequential read from file specified by File Control Block
15h sequential write to file specified by File Control Block
16h find or create firectory entry for file
17h rename file specified by file control block
18h* unknown
19h return current disk drive
1Ah set disk transfer area (DTA)
1Bh get current disk drive FAT
1Ch get disk FAT for any drive
1Dh* unknown
1Eh* unknown
1Fh* read DOS disk block, default drive
20h* unknown
21h random read from file specified by FCB
22h random write to file specified by FCB
23h return number of records in file specified by FCB
24h set relative file record size field for file specified by FCB
25h set interrupt vector
26h create new Program Segment Prefix (PSP)
27h random file block read from file specified by FCB
28h random file block write to file specified by FCB
29h parse the command line for file name
2Ah get the system date
2Bh set the system date
2Ch get the system time
2Dh set the system time
2Eh set/clear disk write VERIFY
2Fh get the Disk Transfer Address (DTA)
30h get DOS version number
31h TSR, files opened remain open
32h* read DOS Disk Block
33h get or set Ctrl-Break
34h* INDOS Critical Section Flag
35h get segment and offset address for an interrupt
36h get free disk space
37h* get/set option marking character (SWITCHAR)
38h return country-dependent information
39h create subdirectory
3Ah remove subdirectory
3Bh change current directory
3Ch create and return file handle
3Dh open file and return file handle
3Eh close file referenced by file handle
3Fh read from file referenced by file handle
40h write to file referenced by file handle
41h delete file
42h move file pointer (move read-write pointer for file)
43h set/return file attributes
44h device IOCTL (I/O control) info
45h duplicate file handle
46h force a duplicate file handle
47h get current directory
48h allocate memory
49h release allocated memory
4Ah modify allocated memory
4Bh load or execute a program
4Ch terminate prog and return to DOS
4Dh get return code of subprocess created by 4Bh
4Eh find first matching file
4Fh find next matching file
50h* set new current Program Segment Prefix (PSP)
51h* puts current PSP into BX
52h* pointer to the DOS list of lists
53h* translates BPB (Bios Parameter Block, see below)
54h get disk verification status (VERIFY)
55h* create PSP: similar to function 26h
56h rename a file
57h get/set file date and time
58h get/set allocation strategy (DOS 3.x)
59h get extended error information
5Ah create a unique filename
5Bh create a DOS file
5Ch lock/unlock file contents
5Dh* network
5Eh* network printer
5Fh* network redirection
60h* parse pathname
61h* unknown
62h get program segment prefix (PSP)
63h* get lead byte table (DOS 2.25)
64h* unknown
65h get extended country information (DOS 3.3)
66h get/set global code page table (DOS 3.3)
67h set handle count (DOS 3.3)
68h commit file (DOS 3.3)
69h disk serial number (DOS 4.0)
6Ah unknown
6Bh unknown
6Ch extended open/create (DOS 4.0)


CALLING THE DOS SERVICESÃÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ

The DOS services are invoked by placing the number of the desired function in
register AH, subfunction in AL, setting the other registers to any specific
requirements of the function, and invoking int 21h.

On return, the requested service will be performed if possible. Most codes
will return an error; some return more information. Details are contained in
the listings for the individual functions. Extended error return may be
obtained by calling function 59h (see 59h).

Register settings listed are the ones used by DOS. Some functions will return
with garbage values in unused registers. Do not test for values in unspecified
registers; your program may exhibit odd behavior.

DS:DX pointers are the data segment register (DS) indexed to the DH and DL
registers (DX). DX always contains the offset address, DS contains the segment
address.

The File Control Block services (FCB services) were part of DOS 1.0. Since
the release of DOS 2.0, Microsoft has recommended that these services not be
used. A set of considerably more enhanced services (handle services) were
introduced with DOS 2.0. The handle services provide support for wildcards and
subdirectories, and enhanced error detection via function 59h.

The data for the following calls was compiled from various Intel, Microsoft,
IBM, and other publications. There are many subtle differences between MSDOS
and PCDOS and between the individual versions. Differences between the
versions are noted as they occur.

There are various ways of calling the DOS functions. For all methods, the
function number is loaded into register AH, subfunctions and/or parameters are
loaded into AL or other registers, and call int 21 by one of the following
methods:
A) call interrupt 21h directly (the recommended procedure)
B) perform a long call to offset 50h in the program's PSP.
1) This method will not work under DOS 1.x
2) Though recommended by Microsoft for DOS 2.0, this method takes more
time and is no longer recommended.
C) place the function number in CL and perform an intrasegment call to
location 05h in the current code segment. This location contains a long
call to the DOS function dispatcher.
1) IBM recommends this method be used only when using existing programs
written for different calling conventions. (such as converting CP/M
programs). This method should be avoided unless you have some specific
use for it.
2) AX is always destroyed by this method.
3) This method is valid only for functions 00h-24h.

There are also various ways of exiting from a program. (assuming it is not
intended to be a TSR). All methods except call 4Ch must ensure that the
segment register contains the segment address of the PSP.
A) Interrupt 21h, function 4Ch (Terminate with Result Code). This is the
"official" recommended method of returning to DOS.
B) Interrupt 21h, function 00h (Exit Program). This is the early style
int 21 function call. It simply calls int 20h.
C) Interrupt 20h (Exit).
D) A JMP instruction to offset 00h (int 20h vector) in the Program Segment
Prefix. This is just a roundabout method to call int 20h. This method
was set up in DOS 1.0 for ease of conversion for CP/M programs. It is no
longer recommended for use.
E) A JMP instruction to offset 05h (int 21 vector) in the Program Segment
Prefix, with AH set to 00h or 4Ch. This is another CP/M type function.




INT 21H DOS services
Function (hex)

* Indicates Functions not documented in the IBM DOS Technical Reference.
Note some functions have been documented in other Microsoft or licensed OEM
documentation.


Function 00h Terminate Program
Ends program, updates, FAT, flushes buffers, restores registers
entry AH 00h
CS segment address of PSP
return none
note 1) Program must place the segment address of the PSP control block in CS
before calling this function.
2) The terminate, ctrl-break,and critical error exit addresses (0Ah, 0Eh,
12h) are restored to the values they had on entry to the terminating
program, from the values saved in the program segment prefix at
locations PSP:000Ah, PSP:000Eh, and PSP:0012h.
3) All file buffers are flushed and the handles opened by the process are
closed.
4) Any files that have changed in length and are not closed are not
recorded properly in the directory.
5) Control transfers to the terminate address.
6) This call performs exactly the same function as int 20h.
7) All memory used by the program is returned to DOS.


Function 01h Get Keyboard Input
Waits for char at STDIN (if nescessary), echoes to STDOUT
entry AH 01h
return AL ASCII character from STDIN (8 bits)
note 1) Checks char for Ctrl-C, if char is Ctrl-C, executes int 23h.
2) For function call 06h, extended ASCII codes require two function calls.
The first call returns 00h as an indicator that the next call will be an
extended ASCII code.
3) Input and output are redirectable. If redirected, there is no way to
detect EOF.


Function 02h Display Output
Outputs char in DL to STDOUT
entry AH 02h
DL 8 bit data (usually ASCII character)
return none
note 1) If char is 08 (backspace) the cursor is moved 1 char to the left
(nondestructive backspace).
2) If Ctrl-C is detected after input, int 23h is executed.
3) Input and output are redirectable. If redirected, there is no way to
detect disk full.


Function 03h Auxiliary Input
Get (or wait until) character from STDAUX
entry AH 03h
return AL char from auxiliary device
note 1) AUX, COM1, COM2 is unbuffered and not interrupt driven
2) This function call does not return status or error codes. For greater
control it is recommended that you use ROM BIOS routine (int 14h) or
write an AUX device driver and use IOCTL.
3) At startup, PC-DOS initializes the first auxiliary port (COM1) to 2400
baud, no parity, one stop bit, and an 8-bit word. MSDOS may differ.
4) If Ctrl-C is has been entered from STDIN, int 23h is executed.


Function 04h Auxiliary Output
Write character to STDAUX
entry AH 04h
DL char to send to AUX
return none
note 1) This function call does not return status or error codes. For greater
control it is recommended that you use ROM BIOS routine (int 14h) or
write an AUX device driver and use IOCTL.
2) If Ctrl-C is has been entered from STDIN, int 23h is executed.
3) Default is COM1 unless redirected by DOS.
4) If the device is busy, this function will wait until it is ready.


Function 05h Printer Output
Write character to STDPRN
entry AL 05h
DL character to send
return none
note 1) If Ctrl-C is has been entered from STDIN, int 23h is executed.
2) Default is PRN or LPT1 unless redirected with the MODE command.
3) If the printer is busy, this function will wait until it is ready.


Function 06h Direct Console I/O
Get character from STDIN; echo character to STDOUT
entry AH 06h
DL 0FFh for console input, or 00h-0FEh for console output
return ZF set (1) = no character
clear (0) = character recieved
AL character
note 1) Extended ASCII codes require two function calls. The first call returns
00h to indicate the next call will return an extended code.
2) If DL is not 0FFh, DL is assumed to have a valid character that is
output to STDOUT.
3) This function does not check for Ctrl-C or Ctrl-PrtSc.
4) Does not echo input to screen
5) If I/O is redirected, EOF or disk full cannot be detected.


Function 07h Direct Console Input Without Echo (does not check BREAK)
Get or wait for char at STDIN, returns char in AL
entry AH 07h
return AL character from standard input device
note 1) Extended ASCII codes require two function calls. The first call returns
00h to indicate the next call will return an extended code.
2) No checking for Ctrl-C or Ctrl-PrtSc is done.
3) Input is redirectable.


Function 08h Console Input Without Echo (checks BREAK)
Get or Wait for char at STDIN, return char in AL
entry AH 08h
return AL char from standard input device
note 1) Char is checked for ctrl-C. If ctrl-C is detected, executes int 23h.
2) For function call 08h, extended ASCII characters require two function
calls. The first call returns 00h to signify an extended ASCII code.
The next call returns the actual code.
3) Input is redirectable. If redirected, there is no way to check EOF.


Function 09h Print String
Outputs Characters in the Print String to the STDOUT
entry AH 09h
DS:DX pointer to the Character String to be displayed
return none
note 1) The character string in memory must be terminated by a $ (24h)
The $ is not displayed.
2) Output to STDOUT is the same as function call 02h.


Function 0Ah Buffered Keyboard Input
Reads characters from STDIN and places them in the buffer beginning
at the third byte.
entry AH 0Ah
DS:DX pointer to an input buffer
return none
note 1) Min buffer size = 1, max = 255
2) Char is checked for ctrl-C. If ctrl-C is detected, executes int 23h.
3) Format of buffer DX:
byte contents
1 Maximum number of chars the buffer will take, including CR.
Reading STDIN and filling the buffer continues until a carriage
return ( or 0Dh) is read. If the buffer fills to one less
than the maximum number the buffer can hold, each additional
number read is ignored and ASCII 7 (BEL) is output to the
display until a carriage return is read. (you must set this
value)
2 Actual number of characters received, excluding the carriage
return, which is always the last character. (the function sets
this value)
3-n Characters received are placed into the buffer starting here.
Buffer must be at least as long as the number in byte 1.
4) Input is redirectable. If redirected, there is no way to check EOF.
5) The string may be edited with the standard DOS editing commands as it
is being entered.
6) Extended ASCII characters are stored as 2 bytes, the first byte being
zero.


Function 0Bh Check Standard Input (STDIN) status
Checks for character availible at STDIN
entry AH 0Bh
return AL 0FFh if a character is availible from STDIN
00h if no character is availible from STDIN
note 1) Checks for Ctrl-C. If Ctrl-C is detected, int 23h is executed
2) Input can be redirected.
3) Checks for character only, it is not read into the application
4) IBM reports that this call does not work properly under the DOSSHELL
program in DOS 4.00 and 4.01. DOSSHELL will return all zeroes. This
function works correctly from the command line or application.


Function 0Ch Clear Keyboard Buffer & Invoke a Keyboard Function (FCB)
Dumps buffer, executes function in AL (01h,06h,07h,08h,0Ah only)
entry AH 0Ch
AL function number (must be 01h, 06h, 07h, 08h, or 0Ah)
return AL 00h buffer was flushed, no other processing performed
other any other value has no meaning
note 1) Forces system to wait until a character is typed.
2) Flushes all typeahead input, then executes function specified by AL (by
moving it to AH and repeating the int 21 call).
3) If AL contains a value not in the list above, the keyboard buffer is
flushed and no other action is taken.


Function 0Dh Disk Reset
Flushes all currently open file buffers to disk
entry AH 0Dh
return none
note 1) Does not close files. Does not update directory entries; files changed
in size but not closed are not properly recorded in the directory
2) Sets DTA address to DS:0080h
3) Should be used before a disk change, Ctrl-C handlers, and to flush
the buffers to disk.


Function 0Eh Select Disk
Sets the drive specified in DL (if valid) as the default drive
entry AL 0Eh
DL new default drive number (0=A:,1=B:,2=C:,etc.)
return AL total number of logical drives (not nescessarily physical)
note 1) For DOS 1.x and 2.x, the minimum value for AL is 2.
2) For DOS 3.x and 4.x, the minimum value for AL is 5.
3) The drive number returned is not nescessarily a valid drive.
4) For DOS 1.x: 16 logical drives are availible, A-P.
For DOS 2.x: 63 logical drives are availible. (Letters are only used for
the first 26 drives. If more than 26 logical drives are
used, further drive letters will be other ASCII characters
ie {,], etc.
For DOS 3.x: 26 logical drives are availible, A-Z.
For DOS 4.x: 26 logical drives are availible, A-Z.


Function 0Fh Open Disk File (FCB)
Searches current directory for specified filename and opens it
entry AH 0Fh
DS:DX pointer to an unopened FCB
return AL 00h if file found
0FFh if file not not found
note 1) If the drive code was 0 (default drive) it is changed to the actual
drive used (1=A:,2=B:,3=C:, etc). This allows changing the default drive
without interfering with subsequent operations on this file.
2) The current block field (FCB bytes C-D, offset 0Ch) is set to zero.
3) The size of the record to be worked with (FCB bytes E-F, offset 0Eh) is
set to the system default of 80h. The size of the file (offset 10h) and
the date (offset 14h) are set from information obtained in the root
directory. You can change the default value for the record size (FCB
bytes E-F) or set the random record size and/or current record field.
Perform these actions after the open but before any disk operations.
4) The file is opened in compatibility mode.
5) Microsoft recommends handle function call 3Dh be used instead.
6) This call is also used by the APPEND command in DOS 3.2+
7) Before performing a sequential disk operation on the file, you must
set the Current Record field (offset 20h). Before performing a random
disk operation on the file, you must set the Relative Record field
(offset 21h). If the default record size of 128 bytes is incorrect, set
it to the correct value.


Function 10h Close File (FCB)
Closes a File After a File Write
entry AH 10h
DS:DX pointer to an opened FCB
return AL 00h if the file is found and closed
0FFh if the file is not found in the current directory
note 1) This function call must be done on open files that are no longer needed,
and after file writes to insure all directory information is updated.
2) If the file is not found in its correct position in the current
directory, it is assumed that the diskette was changed and AL returns
0FFh. This error return is reportedly not completely reliable with DOS
version 2.x.
3) If found, the directory is updated to reflect the status in the FCB, the
buffers to that file are flushed, and AL returns 00h.


Function 11h Search For First Matching Entry (FCB)
Searches current disk & directory for first matching filename
entry AH 11h
DS:DX pointer to address of FCB
return AL 00h successful match
0FFh no matching filename found
note 1) The FCB may contain the wildcard character ? under Dos 2.x, and ? or *
under 3.x and 4.x.
2) The original FCB at DS:DX contains information to continue the search
with function 12h, and should not be modified.
3) If a matching filename is found, AL returns 00h and the locations at the
Disk Transfer Address are set as follows:
a) If the FCB provided for searching was an extended FCB, then the first
byte at the disk transfer address is set to 0FFh followed by 5 bytes
of zeroes, then the attribute byte from the search FCB, then the
drive number used (1=A, 2=B, etc) then the 32 bytes of the directory
entry. Thus, the disk transfer address contains a valid unopened FCB
with the same search attributes as the search FCB.
b) If the FCB provided for searching was a standard FCB, then the first
byte is set to the drive number used (1=A,2=b,etc), and the next 32
bytes contain the matching directory entry. Thus, the disk transfer
address contains a valid unopened normal FCB.
4) If an extended FCB is used, the following search pattern is used:
a) If the FCB attribute byte is zero, only normal file entries are
found. Entries for volume label, subdirectories, hidden or system
files, are not returned.
b) If the attribute byte is set for hidden or system files, or
subdirectory entries, it is to be considered as an inclusive search.
All normal file entries plus all entries matching the specified
attributes are returned. To look at all directory entries except the
volume label, the attribute byte may be set to hidden + system +
directory (all 3 bits on).
c) If the attribute field is set for the volume label, it is considered
an exclusive search, and ONLY the volume label entry is returned.
5) This call is also used by the APPEND command in DOS 3.2+


Function 12h Search For Next Entry Using FCB (FCB)
Search for next matching filename
entry AH 12h
DS:DX pointer to the unopened FCB specified from the previous Search
First (11h) or Search Next (12h)
return AL 00h if matching filename found
0FFh if matching filename was not found
note 1) After a matching filename has been found using function call 11h,
function 12h may be called to find the next match to an ambiguous
request. For DOS 2.x, ?'s are allowed in the filename. For DOS 3.x
and 4.x, global (*) filename characters are allowed.
2) The DTA contains info from the previous Search First or Search Next.
3) All of the FCB except for the name/extension field is used to keep
information nescessary for continuing the search, so no disk operations
may be performed with this FCB between a previous function 11h or 12h
call and this one.
4) If the file is found, an FCB is created at the DTA address and set up to
open or delete it.


Function 13h Delete File Via FCB (FCB)
Deletes file specified in FCB from current directory
entry AH 13h
DS:DX pointer to address of FCB
return AL 00h file deleted
0FFh if file not found or was read-only
note 1) All matching current directory entries are deleted. The global filename
character "?" is allowed in the filename.
2) Will not delete files with read-only attribute set
3) Close open files before deleting them.
4) Requires Network Access Rights


Function 14h Sequential Disk File Read (FCB)
Reads record sequentially from disk via FCB
entry AH 14h
DS:DX pointer to an opened FCB
return AL 00h successful read
01h end of file (no data read)
02h Data Transfer Area too small for record size specified
or segment overflow
03h partial record read, EOF found
note 1) The record size is set to the value at offset 0Eh in the FCB.
2) The record pointed to by the Current Block (offset 0Ch) and the Current
Record (offset 20h) fields is loaded at the DTA, then the Current Block
and Current Record fields are incremented.
3) The record is read into memory at the current DTA address as specified
by the most recent call to function 1Ah. If the size of the record and
location of the DTA are such that a segment overflow or wraparound would
occur, the error return is set to AL=02h
4) If a partial record is read at the end of the file, it is passed to the
requested size with zeroes and the error return is set to AL=03h.


Function 15h Sequential Disk Write (FCB)
Writes record specified by FCB sequentially to disk
entry AH 15h
DS:DX pointer to address of FCB
return AL 00h successful write
01h diskette full, write canceled
02h disk transfer area (DTA) too small or segment wrap
note 1) The data to write is obtained from the disk transfer area
2) The record size is set to the value at offset 0Eh in the FCB.
3) This service cannot write to files set as read-only
4) The record pointed to by the Current Block (offset 0Ch) and the Current
Record (offset 20h) fields is loaded at the DTA, then the Current Block
and Current Record fields are incremented.
5) If the record size is less than a sector, the data in the DTA is written
to a buffer; the buffer is written to disk when it contains a full
sector of data, the file is closed, or a Reset Disk (function 0Dh) is
issued.
6) The record is written to disk at the current DTA address as specified
by the most recent call to function 1Ah. If the size of the record and
location of the DTA are such that a segment overflow or wraparound would
occur, the error return is set to AL=02h


Function 16h Create A Disk File (FCB)
Search and open or create directory entry for file
entry AH 16h
DS:DX pointer to an FCB
return AL 00h successful creation
0FFh no room in directory
note 1) If a matching directory entry is found, the file is truncated to zero
bytes.
2) If there is no matching filename, a filename is created.
3) This function calls function 0Fh (Open File) after creating or
truncating a file.
4) A hidden file can be created by using an extended FCB with the attribute
byte (offset FCB-1) set to 2.


Function 17h Rename File Specified by File Control Block (FCB)
Renames file in current directory
entry AH 17h
DS:DX pointer to an FCB (see note 4)
return AL 00h successfully renamed
0FFh file not found or filename already exists
note 1) This service cannot rename read-only files
2) The "?" wildcard may be used.
3) If the "?" wildcard is used in the second filename, the corresponding
letters in the filename of the directory entry are not changed.
4) The FCB must have a drive number, filename, and extension in the usual
position, and a second filename starting 6 bytes after the first, at
offset 11h.
5) The two filenames cannot have the same name.
6) FCB contains new name starting at byte 17h.


Function 18h Internal to DOS
* Unknown
entry AH 18h
return AL 0


Function 19h Get Current Disk Drive
Return designation of current default disk drive
entry AH 19h
return AL current default drive (0=A, 1=B,etc.)
note Some other DOS functions use 0 for default, 1=A, 2=B, etc.


Function 1Ah Set Disk Transfer Area Address (DTA)
Sets DTA address to the address specified in DS:DX
entry AH 1Ah
DS:DX pointer to buffer
return none
note 1) The default DTA is 128 bytes at offset 80h in the PSP. DOS uses the
DTA for all file I/O.
2) Registers are unchanged.
3) No error codes are returned.
2) Disk transfers cannot wrap around from the end of the segment to the
beginning or overflow into another segment.


Function 1Bh Get Current Drive File Allocation Table Information
Returns information from the FAT on the current drive
entry AH 1Bh
exit AL number of sectors per allocation unit (cluster)
DS:BX address of the current drive's media descriptor byte
CX number of bytes per sector
DX number of allocation units (clusters) for default drive
note 1) Save DS before calling this function.
2) This call returned a pointer to the FAT in DOS 1.x. Beginning with
DOS 2.00, it returns a pointer only to the table's ID byte.
3) IBM recommends programmers avoid this call and use int 25h instead.


Function 1Ch Get File Allocation Table Information for Specific Device
Returns information on specified drive
entry AH 1Ch
DL drive number (1=A, 2=B, 3=C, etc)
return AL number of sectors per allocation unit (cluster)
DS:BX address of media descriptor byte for drive in DL
CX sector size in bytes
DX number of allocation units (clusters)
note 1) DL = 0 for default.
2) Save DS before calling this function.
3) Format of media-descriptor byte:
bits: 0 0 (clear) not double sided
1 (set) double sided
1 0 (clear) not 8 sector
1 (set) 8 sector
2 0 (clear) nonremovable device
1 (set) removable device
3-7 always set (1)
4) This call returned a pointer to the FAT in DOS 1.x. Beginning with
DOS 2.00, it returns a pointer only to the table's ID byte.
5) IBM recommends programmers avoid this call and use int 25h instead.


Function 1Dh Not Documented by Microsoft
* Unknown
entry AH 1Dh
return AL 0


Function 1Eh Not Documented by Microsoft
* Unknown
entry AH 1Eh
return AL 0
note Apparently does nothing


Function 1Fh Get Default Drive Parameter Block
* Same as function call 32h (below), except that the table is accessed from
the default drive
entry AH 1Fh
other registers unknown
return AL 00h no error
0FFh error
DS:BX points to DOS Disk Parameter Block for default drive.
note 1) Unknown vector returned in ES:BX.
2) For DOS 2.x and 3.x, this just invokes function 32h (undocumented,
Read DOS Disk Block) with DL=0


Function 20h Unknown
* Internal - does nothing?
entry AH 20h
return AL 0


Function 21h Random Read from File Specified by File Control Block (FCB)
Reads one record as specified in the FCB into the current DTA.
entry AH 21h
DS:DX address of the opened FCB
return AL 00h successful read operation
01h end of file (EOF), no data read
02h DTA too small for the record size specified
03h end of file (EOF), partial data read
note 1) The current block and current record fields are set to agree with the
random record field. Then the record addressed by these fields is read
into memory at the current Disk Transfer Address.
2) The current file pointers are NOT incremented this function.
3) If the DTA is larger than the file, the file is padded to the requested
length with zeroes.


Function 22h Random Write to File Specified by FCB (FCB)
Writes one record as specified in the FCB to the current DTA
entry AH 22h
DS:DX address of the opened FCB
return AL 00h successful write operation
01h disk full; no data written (write was canceled)
02h DTA too small for the record size specified (write was
canceled)
note 1) This service cannot write to read-only files.
2) The record pointed to by the Current Block (offset 0Ch) and the Current
Record (offset 20h) fields is loaded at the DTA, then the Current Block
and Current Record fields are incremented.
3) If the record size is less than a sector, the data in the DTA is written
to a buffer; the buffer is written to disk when it contains a full
sector of data, the file is closed, or a Reset Disk (function 0Dh) is
issued.
4) The current file pointers are NOT incremented this function.
5) The record is written to disk at the current DTA address as specified
by the most recent call to function 1Ah. If the size of the record and
location of the DTA are such that a segment overflow or wraparound would
occur, the error return is set to AL=02h


Function 23h Get File Size (FCB)
Searches current subdirectory for matching file, returns size in FCB
entry AH 23h
DS:DX address of an unopened FCB
return AL 00h file found
0FFh file not found
note 1) Record size field (offset 0Eh) must be set before invoking this function
2) The disk directory is searched for the matching entry. If a matching
entry is found, the random record field is set to the number of records
in the file. If the value of the Record Size field is not an even
divisor of the file size, the value set in the relative record field is
rounded up. This gives a returned value larger than the actual file size
3) This call is used by the APPEND command in DOS 3.2+


Function 24h Set Relative Record Field (FCB)
Set random record field specified by an FCB
entry AH 24h
DS:DX address of an opened FCB
return Random Record Field of FCB is set to be same as Current Block
and Current Record.
note 1) You must invoke this function before performing random file access.
2) The relative record field of FCB (offset 21h) is set to be same as the
Current Block (offset 0Ch) and Current Record (offset 20h).
3) No error codes are returned.
4) The FCB must already be opened.


Function 25h Set Interrupt Vector
Sets the address of the code DOS is to perform each time the specified
interrupt is invoked.
entry AH 25h
AL int number to reassign the handler to
DS:DX address of new interrupt vector
return none
note 1) Registers are unchanged.
2) No error codes are returned.
3) The interrupt vector table for the interrupt number specified in AL
is set to the address contained in DS:DX. Use function 35h (Get Vector)
to get the contents of the interrupt vector and save it for later use.
4) When you use function 25 to set an interrupt vector, DOS 3.2 doesn't
point the actual interrupt vector to what you requested. Instead, it
sets the interrupt vector to point to a routine inside DOS, which does
this:
1. Save old stack pointer
2. Switch to new stack pointer allocated from DOS's stack pool
3. Call your routine
4. Restore old stack pointer
The purpose for this was to avoid possible stack overflows when there
are a large number of active interrupts. IBM was concerned (this was an
IBM change, not Microsoft) that on a Token Ring network there would be
a lot of interrupts going on, and applications that hadn't allocated
very much stack space would get clobbered.


Function 26h Create New Program Segment Prefix (PSP)
This service copies the current program-segment prefix to a new memory
location for the creation of a new program or overlay. Once the new PSP is
in place, a DOS program can read a DOS COM or overlay file into the memory
location immediately following the new PSP and pass control to it.
entry AH 26h
DX segment number for the new PSP
return none
note 1) Microsoft recommends you use the newer DOS service 4Bh (EXEC) instead.
2) The entire 100h area at location 0 in the current PSP is copied into
location 0 of the new PSP. The memory size information at location 6
in the new segment is updated and the current termination, ctrl-break,
and critical error addresses from interrupt vector table entries for
ints 22h, 23h, and 24 are saved in the new program segment starting at
0Ah. They are restored from this area when the program terminates.
3) Current PSP is copied to specified segment


Function 27h Random Block Read From File Specified by FCB
Similar to 21h (Random Read) except allows multiple files to be read.
entry AH 27h
CX number of records to be read
DS:DX address of an opened FCB
return AL 00h successful read
01h end of file, no data read
02h DTA too small for record size specified (read canceled)
03h end of file
CX actual number of records read (includes partial if AL=03h)
note 1) The record size is specified in the FCB. The service updates the Current
Block (offset 0Ch) and Current Record (offset 20h) fields to the next
record not read.
2) If CX contained 0 on entry, this is a NOP.
3) If the DTA is larger than the file, the file is padded to the requested
length with zeroes.
4) This function assumes that the FCB record size field (0Eh) is correctly
set. If not set by the user, the default is 128 bytes.
5) The record is written to disk at the current DTA address as specified
by the most recent call to function 1Ah. If the size of the record and
location of the DTA are such that a segment overflow or wraparound would
occur, the error return is set to AL=02h


Function 28h Random Block Write to File Specified in FCB
Similar to 27h (Random Write) except allows multiple files to be read.
entry AH 28h
CX number of records to write
DS:DX address of an opened FCB
return AL 00h successful write
01h disk full, no data written
02h DTA too small for record size specified (write canceled)
CX number of records written
note 1) The record size is specified in the FCB.
2) This service allocates disk clusters as required.
3) This function assumes that the FCB Record Size field (offset 0Eh) is
correctly set. If not set by the user, the default is 128 bytes.
4) The record size is specified in the FCB. The service updates the Current
Block (offset 0Ch) and Current Record (offset 20h) fields to the next
record not read.
5) The record is written to disk at the current DTA address as specified
by the most recent call to function 1Ah. If the size of the record and
location of the DTA are such that a segment overflow or wraparound would
occur, the error return is set to AL=02h
6) If called with CX=0, no records are written, but the FCB's File Size
entry (offset 1Ch) is set to the size specified by the FCB's Relative
Record field (offset 21h).


Function 29h Parse the Command Line for Filename
Parses a text string into the fields of a File Control Block
entry AH 29h
DS:SI pointer to string to parse
ES:DI pointer to memory buffer to fill with unopened FCB
AL bit mask to control parsing
bit 0 = 0: parsing stops if file seperator found
1: causes service to scan past leading chars such as
blanks. Otherwise assumes the filename begins in
the first byte
1 = 0: drive number in FCB set to default (0) if string
contains no drive number
1: drive number in FCB not changed
2 = 0: filename in FCB set to 8 blanks if no filename in
string
1: filename in FCB not changed if string does not
contain a filename
3 = 0: extension in FCB set to 3 blanks if no extension in
string
1: extension left unchanged
4-7 must be zero
return AL 00h no wildcards in name or extension
01h wildcards appeared in name or extension
0FFh invalid drive specifier
DS:SI pointer to the first byte after the parsed string
ES:DI pointer to a buffer filled with the unopened FCB
note 1) If the * wildcard characters are found in the command line, this service
will replace all subsequent chars in the FCB with question marks.
2) This service uses the characters as filename separators
DOS 1 : ; . , + / [ ] = " TAB SPACE
DOS 2,3 : ; . , + = TAB SPACE
3) This service uses the characters
: ; . , + < > | / \ [ ] = " TAB SPACE
or any control characters as valid filename separators
4) A filename cannot contain a filename terminator. If one is encountered,
all processing stops. The handle functions will allow use of some of
these characters.
5) If no valid filename was found on the command line, ES:DI +1 points
to a blank (ASCII 32).
6) This function cannot be used with filespecs which include a path
7) Parsing is in the form D:FILENAME.EXT. If one is found, a corresponding
unopened FCB is built at ES:DI


Function 2Ah Get Date
Returns day of the week, year, month, and date
entry AH 2Ah
return CX year (1980-2099)
DH month (1-12)
DL day (1-31)
AL weekday 00h Sunday
01h Monday
02h Tuesday
03h Wednesday
04h Thursday
05h Friday
06h Saturday
note 1) Date is adjusted automatically if clock rolls over to the next day,
and takes leap years and number of days in each month into account.
2) Although DOS cannot set an invalid date, it can read one, such as
1/32/80, etc.
3) DesQview also accepts CX = 4445h and DX = 5351h, i.e. 'DESQ' as valid
4) DOS will accept CH=0 (midnight) as a valid time, but if a file's time
is set to exactly midnight the time will not be displayed by the DIR
command.


Function 2Bh Set Date
set current system date
entry AH 2Bh
CX year (1980-2099)
DH month (1-12)
DL day (1-31)
return AL 00h no error (valid date)
0FFh invalid date specified
note 1) On entry, CX:DX must have a valid date in the same format as returned
by function call 2Ah
2) DOS 3.3 also sets CMOS clock


Function 2Ch Get Time
Get current system time from CLOCK$ driver
entry AH 2Ch
return CH hours (0-23)
CL minutes (0-59)
DH seconds (0-59)
DL hundredths of a second (0-99)
note 1) Time is updated every 5/100 second.
2) The date and time are in binary format


Function 2Dh Set Time
Sets current system time
entry AH 2Dh
CH hours (0-23)
CL minutes (0-59)
DH seconds (0-59)
DL hundredths of seconds (0-99)
return AL 00h if no error
0FFh if bad value sent to routine
note 1) DOS 3.3 also sets CMOS clock
2) CX and DX must contain a valid time in binary


Function 2Eh Set/Reset Verify Switch
Set verify flag
entry AH 2Eh
AL 00 to turn verify off (default)
01 to turn verify on
return none
note 1) This is the call invoked by the DOS VERIFY command
2) Setting of the verify switch can be obtained by calling call 54h
3) This call is not supported on network drives
4) DOS checks this flag each time it accesses a disk


Function 2Fh Get Disk Transfer Address (DTA)
Returns current disk transfer address used by all DOS read/write operations
entry AH 2Fh
return ES:BX address of DTA
note 1) The DTA is set by function call 1Ah
2) Default DTA address is a 128 byte buffer at offset 80h in that program's
Program Segment Prefix


Function 30h Get DOS Version Number
Return DOS version and/or user number
entry AH 30h
return AH minor version number (i.e., DOS 2.10 returns AX = 0A02h)
AL major version number
BH OEM ID number
00h IBM
16h DEC (others not known)
BL:CX 24-bit user serial number
note 1) If AL returns a major version number of zero, the DOS version is
below 1.28 for MSDOS and below 2.00 for PCDOS.
2) IBM PC-DOS always returns 0000h in BX and CX.
3) OS/2 v1.0 Compatibility Box returns a value of 10 for major version.
4) Due to the OS/2 return and the fact that some European versions of DOS
carry higher version numbers than IBM's DOS, utilities which check
for a DOS version should not abort if a higher version than required
is found unless some specific problems are known.


Function 31h Terminate Process and Stay Resident
KEEP, or TSR
entry AH 31h
AL exit code
DX program memory requirement in 16 byte paragraphs
return AX return code (retrieveable by function 4Dh)
note 1) Files opened by the application are not closed when this call is made
2) Memory can be used more efficiently if the block containing the copy of
the DOS environment is deallocated before terminating. This can be done
by loading ES with the segment contained in 2Ch of the PSP and issuing
function call 49h (Free Allocated Memory).
3) Unlike int 27h, more than 64k may be made resident with this call


Function 32h Read DOS Disk Block
* Retrieve the pointer to the drive parameter block for a drive
entry AH 32h
DL drive (0=default, 1=A:, etc.).
return AL 00h if drive is valid
0FFh if drive is not valid
DS:BX pointer to DOS Drive Parameter Table. Format of block:
Bytes Type Value
00h byte Drive: 0=A:, 1=B:, etc.
01h byte Unit within drive (0, 1, 2, etc.)
02h-03h word Bytes per sector
04h byte Sectors per cluster - 1
05h byte Cluster to sector shift (i.e., how far to shift-
left the bytes/sector to get bytes/cluster)
06h-07h word Number of reserved (boot) sectors
08h byte Number of FATs
09h-0Ah word Number of root directory entries
0Bh-0Ch word Sector # of 1st data. Should be same as # of
sectors/track.
0Dh-0Eh word # of clusters + 1 (=last cluster #)
0Fh byte Sectors for FAT
10h-11h word First sector of root directory
12h-15h dword Address of device driver header for this drive
16h byte Media Descriptor Byte for this drive
17h byte 0FFh indicates block must be rebuilt
(DOS 3.x) 00h indicates block device has
been accessed
18h-1Bh dword address of next DOS Disk Block (0FFFFh means
last in chain)
22h byte Current Working Directory (2.0 only) (64 bytes)
note 1) Use [BX+0D] to find no. of clusters (>1000H, 16-bit FAT; if not, 12-bit
(exact dividing line is probably a little below 1000h to allow for
bad sectors, EOF markers, etc.)
2) Short article by C.Petzold, PC Magazine Vol.5,no.8, and the article
"Finding Disk Parameters" in the May 1986 issue of PC Tech Journal.
3) This call is mostly supported in OS/2 1.0's DOS Compatibility Box. The
dword at 12h will not return the address of the next device driver when
in the Compatibility Box.
4) used by CHKDSK


Function 33h Control-Break Check
Get or set control-break checking at CON
entry AH 33h
AL 00h to test for break checking
01h to set break checking
DL 00h to disable break checking
01h to enable break checking
02h internal, called by PRINT.COM (DOS 3.1)
03h unknown
04h unknown
05h boot drive (DOS 4.0+)
return DL 00h if break=off
01h if break=on
(if AL=05h) boot drive, A=1, B=2, etc)
AL 0FFh error


Function 34h Return INDOS Flag
* Returns ES:BX pointing to Critical Section Flag, byte indicating whether
it is safe to interrupt DOS.
entry AH 34h
return ES:BX points to DOS "critical section flag"
note 1) If byte is 0, it is safe to interrupt DOS. This was mentioned in some
documentation by Microsoft on a TSR standard, and PC Magazine reports
it functions reliably under DOS versions 2.0 through 3.3. Chris
Dunford (of CED fame) and a number of anonymous messages on the BBSs
indicate it may not be totally reliable.
2) The byte at ES:BX+1 is used by the Print program for this same purpose,
so it's probably safer to check the WORD at ES:BX.
3) Reportedly, examination of DOS 2.10 code in this area indicates that the
byte immediately following this "critical section flag" must be 00h to
permit the PRINT.COM interrupt to be called. For DOS 3.0 and 3.1 (except
Compaq DOS 3.0), the byte before the "critical section flag" must be
zero; for Compaq DOS 3.0, the byte 01AAh before it must be zero.
4) In DOS 3.10 this reportedly changed to word value, with preceding byte.
5) This call is supported in OS/2 1.0's DOS Compatibility Box
6) Gordon Letwin of Microsoft discussed this call on ARPAnet in 1984. He
stated:
a) this is not supported under any version of the DOS
b) it usually works under DOS 2, but there may be circumstances
when it doesn't (general disclaimer, don't know of a specific
circumstance)
c) it will usually not work under DOS 3 and DOS 3.1; the DOS is
considerably restructured and this flag takes on additional
meanings and uses
d) it will fail catastrophically under DOS 4.0 and forward.
Obviously this information is incorrect since the call works fine
through DOS 3.3. Microsoft glasnost?


Function 35h Get Vector
Get interrupt vector
entry AH 35h
AL interrupt number (hexadecimal)
return ES:BX address of interrupt vector
note Use function call 25h to set the interrupt vectors


Function 36h Get Disk Free Space
get information on specified drive
entry AH 36h
DL drive number (0=default, 1=A:, 2=B:, etc)
return AX number of sectors per cluster
0FFFFh means drive specified in DL is invalid
BX number of availible clusters
CX bytes per sector
DX clusters per drive
note 1) Mult AX * CX * BX for free space on disk
2) Mult AX * CX * DX for total disk space
3) Function 36h returns an incorrect value after an ASSIGN command. Prior
to ASSIGN, the DX register contains 0943h on return, which is the free
space in clusters on the HC diskette. After ASSIGN, even with no
parameters, 0901h is returned in the DX register; this is an incorrect
value. Similar results occur with DD diskettes on a PC-XT or a PC-AT.
This occurs only when the disk is not the default drive. Results are as
expected when the drive is the default drive. Therefore, the
circumvention is to make the desired drive the default drive prior to
issuing this function call.
4) Int 21h, function call 36h returns an incorrect value after an ASSIGN
command. Prior to ASSIGN, the DX register contains 0943h on return,
which is the free space in clusters on the HC diskette. After ASSIGN,
even with no parameters, 0901h is returned in the DX register; this is
an incorrect value. Similar results occur with DD diskettes on a PC-XT
or a PC-AT. This occurs only when the disk is not the default drive.
Results are as expected when the drive is the default drive. Therefore,
the circumvention is to make the desired drive the default drive prior
to issuing this function call.
5) This function supercedes functions 1Bh and 1Ch.


Function 37h SWITCHAR / AVAILDEV
* Get/set option marking character (is usually "/"), and device type
entry AH 37h
AL 00h read switch character (returns current character in DL)
01h set character in DL as new switch character
(DOS 2.x) 02h read device availability (as set by function AL=3) into
DL. A 0 means devices that devices must be accessed in
file I/O calls by /dev/device. A non-zero value means
that devices are accessible at every level of the
directory tree (e.g., PRN is the printer and not a file
PRN).
AL=2 to return flag in DL, AL=3 to set from DL (0 = set,
1 = not set).
(DOS 2.x) 03h get device availability, where:
DL 00h means /dev/ must precede device names
01h means /dev/ need not precede device names
return DL switch character (if AL=0 or 1)
device availability flag (if AL=2 or 3)
AL 0FFh the value in AL was not in the range 0-3.
note 1) Functions 2 & 3 appear not to be implemented for DOS 3.x.
2) It is documented on page 4.324 of the MS-DOS (version 2) Programmer's
Utility Pack (Microsoft - published by Zenith).
3) Works on all versions of IBM PC-DOS from 2.0 through 3.3.1.
4) The SWITCHAR is the character used for "switches" in DOS command
arguments (defaults to '/', as in "DIR/P"). '-' is popular to make a
system look more like UNIX; if the SWITCHAR is anything other than '/',
then '/' may be used instead of '\' for pathnames
5) Ignored by XCOPY, PKARC, LIST
6) SWITCHAR may not be set to any character used in a filename
7) In DOS 3.x you can still read the "AVAILDEV" byte with subfunction 02h
but it always returns 0FFh even if you try to change it to 0 with
subfunction 03h.
8) AVAILDEV=0 means that devices must be referenced in an imaginary
subdirectory "\dev" (similar to UNIX's /dev/*); a filename "PRN.DAT"
can be created on disk and manipulated like any other. If AVAILDEV != 0
then device names are recognized anywhere (this is the default):
"PRN.DAT" is synonymous with "PRN:".
9) These functions reportedly are not supported in the same fashion in
various implementations of DOS.
10) used by DOS 3.3 CHKDSK, BASIC, DEBUG


Function 38h Return Country Dependent Information
(PCDOS 2.0, 2.1, MSDOS 2.00 only)
entry AH 38h
AL function code (must be 0 in DOS 2.x)
DS:DX pointer to 32 byte memory buffer for returned information
return CF set on error
AX error code (02h)
BX country code
DS:DX pointer to buffer filled with country information:
bytes 0,1 date/time format
0 USA standard H:M:S M/D/Y
1 European standard H:M:S D/M/Y
2 Japanese standard H:M:S D:M:Y
byte2 ASCIIZ string currency symbol
byte3 zeroes
byte4 ASCIIZ string thousands separator
byte5 zeroes
byte6 ASCIIZ string decimal separator
byte7 zeroes
bytes 8,1Fh 24 bytes reserved


Function 38h Get Country Dependent Information
(PCDOS 3.x+, MSDOS 2.01+)
entry AH 38h
AL function code
00h to get current country information
01h-0FEh country code to get information for, for countries
with codes less than 255
0FFh to get country information for countries with a code
greater than 255
BX 16 bit country code if AL=0FFh
DS:DX pointer to the memory buffer where the data will be returned
DX 0FFFFh if setting country code rather than getting info
return CF 0 (clear) function completed
1 (set) error
AX error code
02h invalid country code (no table for it)
(if DX <> 0FFFFh)
BX country code (usually international telephone code)
DS:DX pointer to country data buffer
bytes 0,1 date/time format
0 USA standard H:M:S M/D/Y
1 European standard H:M:S D/M/Y
2 Japanese standard H:M:S D:M:Y
bytes 2-6 currency symbol null terminated
byte 07h thousands separator null terminated
byte 08h zeroes
byte 09h decimal separator null terminated
byte 0Ah zeroes
byte 0Bh date separator null terminated
byte 0Ch zeroes
byte 0Dh time separator null terminated
byte 0Eh zeroes
byte 0Fh bit field currency format
bit 0 = 0 if currency symbol precedes the value
1 if currency symbol is after the value
bit 1 = 0 no spaces between value and currency symbol
1 one space between value and currency symbol
bit 2 = 1 set if currency symbol replaces decimal pt
bits 3-7 not defined by Microsoft
byte 10h number of significant decimal digits in currency
(number of places to right of decimal point)
byte 11h time format
bit 0 = 0 12 hour clock
1 24 hour clock
bits 1-7 unknown, probably not used
bytes 12h-15h address of case map routine (FAR CALL, AL = char)
entry AL ASCII code of character to be converted to
uppercase
return AL ASCII code of the uppercase input character
byte 16h data-list separator character
byte 17h zeroes
bytes 18h-21h 5 words reserved
note 1) When an alternate keyboard handler is invoked, the keyboard routine is
loaded into user memory starting at the lowest portion of availible
user memory. The BIOS interrupt vector that services the keyboard is
redirected to the memory area where the new routine resides. Each new
routine takes up about 1.6K of memory and has lookup tables that return
values unique to each language. (KEYBxx in the DOS book)
Once the keyboard interrupt vector is changed by the DOS keyboard
routine, the new routine services all calls unless the system is
returned to the US format by the ctrl-alt-F1 keystroke combination. This
does not change the interrupt vector back to the BIOS location; it
merely passes the table lookup to the ROM locations.
2) Ctrl-Alt-F1 will only change systems with US ROMS to the US layout.
Some systems are delivered with non-US keyboard handler routines in ROM
3) Case mapping call: the segment/offset of a FAR procedure that performs
country-specific lower-to-upper case mapping on ASCII characters 80h to
0FFh. It is called with the character to be mapped in AL. If there is
an uppercase code for the letter, it is returned in AL, if there is no
code or the function was called with a value of less than 80h AL is
returned unchanged.
4) This call is fully implemented in MS-DOS version 2.01 and higher. It
is in version 2.00 but not fully implemented (according to Microsoft)


Function 38h Set Country Dependent Information
entry AH 38h
AL code country code to set information for, for countries
with codes less than 255
0FFh to set country information for countries with a code
greater than 255
BX 16 bit country code if AL=0FFh
DX 0FFFFh
return CF clear successful
set if error
AX error code (02h)


Function 39h Create Subdirectory (MKDIR)
Makes a subdirectory along the indicated path
entry AH 39h
DS:DX address of ASCIIZ pathname string
return flag CF 0 successful
1 error
AX error code if any (3, 5)
note 1) The ASCIIZ string may contain drive and subdirectory.
2) Drive may be any valid drive (not nescessarily current drive)
3) The pathname cannot exceed 64 characters


Function 3Ah Remove Subdirectory (RMDIR)
entry AH 3Ah
DS:DX address of ASCIIZ pathname string
return CF clear successful
set AX error code if any (3, 5, 16)
note 1) The ASCIIZ string may contain drive and subdirectory.
2) Drive may be any valid drive (not nescessarily current drive)
3) The pathname cannot exceed 64 characters


Function 3Bh Change Current Directory (CHDIR)
entry AH 3Bh
DS:DX address of ASCIIZ string
return flag CF 0 successful
1 error
AX error code if any (3)
note 1) The pathname cannot exceed 64 characters
2) The ASCIIZ string may contain drive and subdirectory.
3) Drive may be any valid drive (not nescessarily current drive)


Function 3Ch Create A File (CREAT)
Create a file with handle
entry AH 3Ch
CX attributes for file
00h normal
01h read only
02h hidden
03h system
DS:DX address of ASCIIZ filename string
return flag CF 0 successful creation
1 error
AX 16 bit file handle
or error code (3, 4, 5)
note 1) The ASCIIZ string may contain drive and subdirectory.
2) Drive may be any valid drive (not nescessarily current drive)
3) If the volume label or subdirectory bits are set in CX, they are ignored
4) The file is opened in read/write mode
5) If the file does not exist, it is created. If one of the same name
exists, it is truncated to a length of 0.
6) Good practice is to attempt to open a file with fn 3Dh and jump to an
error routine if successful, create file if 3Dh fails. That way an
existing file will not be truncated and overwritten.


Function 3Dh Open A File
Open disk file with handle
entry AH 3Dh
AL access code byte
(DOS 2.x) bits 0-2 file attribute
000 read only
001 write only
010 read/write
bits 3-7 should be set to zero
(DOS 3.x) bits 0-2 file attribute
000 read only
001 write only
010 read/write
bit 3 reserved
0 should be set to zero
bits 4-6 sharing mode (network)
000 compatibility mode (the way FCBs open files)
001 read/write access denied (exclusive)
010 write access denied
011 read access denied
100 full access permitted
bit 7 inheritance flag
0 file inherited by child process
1 file private to child process
DS:DX address of ASCIIZ pathname string
return flag CF set on error
AX error code
1 error
AX 16 bit file handle
or error code (1, 2, 4, 5, 0Ch)
note 1) Opens any normal, system, or hidden file
2) Files that end in a colon are not opened
3) The rear/write pointer is set at the first byte of the file and the
record size of the file is 1 byte (the read/write pointer can be changed
through function call 42h). The returned file handle must be used for
all subsequent input and output to the file.
4) If the file handle was inherited from a parent process or was
duplicated by DUP or FORCEDUP, all sharing and access restrictions are
also inherited.
5) A file sharing error (error 1) causes an int 24h to execute with an
error code of 2


Function 3Eh Close A File Handle
Close a file and release handle for reuse
entry AH 3Eh
BX file handle
return flag CF 0 successful close
1 error
AX error code if error (6)
note 1) When executed, the file is closed, the directory is updated, and all
buffers for that file are flushed. If the file was changed, the time
and date stamps are changed to current
2) If called with the handle 00000, it will close STDIN (normally the
keyboard).


Function 3Fh Read From A File Or Device
Read from file with handle
entry AH 3Fh
BX file handle
CX number of bytes to read
DS:DX address of buffer
return flag CF 0 successful read
1 error
AX 0 pointer was already at end of file
or number of bytes read
or error code (5, 6)
note 1) This function attempts to transfer the number of bytes specified in CX
to a buffer location. It is not guaranteed that all bytes will be read.
If AX < CX a partial record was read.
2) If performed from STDIN (file handle 0000), the input can be redirected
3) If used to read the keyboard, it will only read to the first CR
4) The file pointer is incremented to the last byte read.


Function 40h Write To A File Or Device
Write to file with handle
entry AH 40h
BX file handle
CX number of bytes to write
DS:DX address of buffer
return flag CF 0 successful write
1 error
AX number of bytes written
or error code (5, 6)
note 1) This call attempts to transfer the number of bytes indicated in CX
from a buffer to a file. If CX and AX do not match after the write,
an error has taken place; however no error code will be returned for
this problem. This is usually caused by a full disk.
2) If the write is performed to STDOUT (handle 0001), it may be redirected
3) To truncate the file at the current position of the file pointer, set
the number of bytes in CX to zero before calling int 21h. The pointer
can be moved to any desired position with function 42h.
4) This function will not write to a file or device marked read-only.
5) May also be used to display strings to CON instead of fn 09h. This
function will write CX bytes and stop; fn 09h will continue to write
until a $ character is found.
6) This is the call that DOS actually uses to write to the screen in DOS
2.x and above.


Function 41h Delete A File From A Specified Subdirectory (UNLINK)
entry AH 41h
DS:DX pointer to ASCIIZ filespec to delete
return CF 0 successful
1 error
AX error code if any (2, 5)
note 1) This function will not work on a file marked read-only
2) Wildcards are not accepted


Function 42h Move a File Read/Write Pointer (LSEEK)
entry AH 42h
AL method code
00h offset from beginning of file
01h offset from present location
02h offset from end of file
BX file handle
CX most significant half of offset
DX least significant half of offset
return AX low offset of new file pointer
DX high offset of new file pointer
CF 0 successful move
1 error
AX error code (1, 6)
note 1) If pointer is at end of file, reflects file size in bytes.
2) The value in DX:AX is the absolute 32 bit byte offset from the beginning
of the file


Function 43h Get/Set file attributes (CHMOD)
entry AH 43h
AL 00h get file attributes
01h set file attributes
CX file attributes to set
bit 0 read only
1 hidden file
2 system file
3 volume label
4 subdirectory
5 written since backup
DS:DX pointer to full ASCIIZ file name
return CF set if error
AX error code (1, 2, 3, 5)
CX file attributes on get
attributes:
01h read only
02h hidden
04h system
0FFh archive
note 1) This call will not change the volume label or directory bits


Function 44h I/O Control for Devices (IOCTL)
Get or Set Device Information
entry AH 44h
AL 00h Get Device Information (from DX)
BX file or device handle
return DX device info
If bit 7 set: (character device)
bit 0: console input device
1: console output device
2: NUL device
3: CLOCK$ device
4: device is special
5: binary (raw) mode
6: not EOF
12: network device (DOS 3.x)
14: can process IOCTL control
strings (func 2-5)
If bit 7 clear: (file)
bits 0-5: block device number
6: file has not been written
12: Network device (DOS 3.x)
15: file is remote (DOS 3.x)
01h Set Device Information (DH must be zero for this call)
DX bits:
0 1 console input device
1 1 console output device
2 1 null device
3 1 clock device
4 1 reserved
5 0 binary mode - don't check for control chars
1 cooked mode - check for control chars
6 0 EOF - End Of File on input
7 device is character device if set, if not, EOF
is 0 if channel has been written, bits 0-5 are
block device number
12 network device
14 1 can process control strings (AL 2-5, can only be
read, cannot be set)
15 n reserved
02h Read CX bytes to device in DS:DX from BX control chan
03h Write Device Control String
BX device handle
CX number of bytes to write
DS:DX pointer to buffer
return AX number of bytes written
04h Read From Block Device (drive number in BL)
BL drive number (0=default)
CX number of bytes to read
DS:DX pointer to buffer
return AX number of bytes read
05h Write to Block Device (drive number in BL)
AX number of bytes transfered
06h Get Input Handle Status
BX file or device handle
return AL 0FFh device ready
00h device not ready
07h Get Output Handle Status
return AL 00h not ready
0FFh ready
note: for DOS 2.x, files are always ready for output
08h Removable Media Bit (DOS 3.x+)
return AX 00h device is removable
01h device is nonremovable
0Fh invalid drive specification
09h Test whether Local or Network Device in BL (DOS 3.x+)
BL drive number (0=default)
return DX attribute word, bit 12 set if device is
remote
0Ah Is Handle in BX Local or Remote? (DOS 3.x+)
BX file handle
return DX (attribute word) bit 15 set if file is remote
0Bh Change Sharing Retry Count to DX (default=3), (DOS 3.x+)
CX delay (default=1)
DX retry count (default=3)
0Ch General IOCTL (DOS 3.3 [3.2?]) allows a device driver to
prepare, select, refresh, and query Code Pages
0Dh Block Device Request (DOS 3.3+)
BL drive number (0=default)
CH major subfunction
CL minor subfunction
40h set device parameters
41h write logical device track
42h format and verify logical device track
60h get device parameters
61h read logical device track
62h verify logical device track
DS:DX pointer to parameter block
0Eh Get Logical Device (DOS 3.3+)
BL drive number (0=default)
return AL=0 block device has only one logical drive
assigned 1..n the last letter used to reference
the device (1=A:,etc)
0Fh Set Logical Device (DOS 3.3+)
BL drive number: 0=default, 1=A:, 2=B:, etc.
BX file handle
CX number of bytes to read or write
DS:DX data or buffer
DX data
return AX number of bytes transferred
or error code (call function 59h for extended error codes)
or status 00h not ready
0FFh ready
CF set if error


Function 45h Duplicate a File Handle (DUP)
entry AH 45h
BX file handle to duplicate
return CF clear AX duplicate handle
set AX error code (4, 6)
note 1) If you move the pointed of one handle, the pointer of the other will
also be moved.
2) The handle in BX must be open


Function 46h Force Duplicate of a Handle (FORCEDUP or CDUP)
Forces handle in CX to refer to the same file at the same
position as BX
entry AH 46h
BX existing file handle
CX new file handle
return CF clear both handles now refer to existing file
set error
AX error code (4, 6)
note 1) If CX was an open file, it is closed first
2) If you move the read/write pointer of either file, both will move
3) The handle in BX must be open


Function 47h Get Current Directory
Places full pathname of current directory/drive into a buffer
entry AH 47h
DL drive (0=default, 1=A:, etc.)
DS:SI points to 64-byte buffer area
return CF clear DS:DI pointer to ASCIIZ pathname of current directory
set AX error code (0Fh)
note String does not begin with a drive identifier or a backslash


Function 48h Allocate Memory
Allocates requested number of 16-byte paragraphs of memory
entry AH 48h
BX number of 16-byte paragraphs desired
return CF clear AX segment address of allocated space
BX maximum number paragraphs available
set AX error code (7, 8)
note BX indicates maximum memory availible only if allocation fails


Function 49h Free Allocated Memory
Frees specified memory blocks
entry AH 49h
ES segment address of area to be freed
return CF clear successful
set AX error code (7, 9)
note 1) This call is only valid when freeing memory obtained by function 48h.
2) A program should not try to release memory not belonging to it.


Function 4Ah Modify Allocated Memory Blocks (SETBLOCK)
Expand or shrink memory for a program
entry AH 4AH
BX new size in 16 byte paragraphs
ES segment address of block to change
return CF clear nothing
set AX error code (7, 8, 9)
or BX max number paragraphs available
note 1) Max number paragraphs availible is returned only if the call fails
2) Memory can be expanded only if there is memory availible


Function 4Bh Load or Execute a Program (EXEC)
entry AH 4Bh
AL 00h load and execute program. A PSP is built for the program
the ctrl-break and terminate addresses are set to the
new PSP.
*01h load but don't execute (note 1)
*01h load but don't execute (internal, DOS 3.x & DESQview)
*02h load but do not execute (internal, DOS 2.x only)
03h load overlay (do not create PSP, do not begin execution)
DS:DX points to the ASCIIZ string with the drive, path, and filename
to be loaded
ES:BX points to a parameter block for the load
(AL=00h) word segment address of environment string to be
passed
dword pointer to the command line to be placed at
PSP+80h
dword pointer to default FCB to be passed at PSP+5Ch
dword pointer to default FCB to be passed at PSP+6Ch
(*AL=01h) word segment of environment (0 = use current)
dword pointer to command line
dword pointer to FCB 1
dword pointer to FCB 2
dword will hold SS:SP on return
dword will hold program entry point (CS:IP) on return
(*AL=02h) word segment of environment (0 = use current)
dword pointer to command line
dword pointer to FCB 1
dword pointer to FCB 2
(AL=03h) word segment address where file will be loaded
word relocation factor to be applied to the image
return CF set error
AX error code (1, 2, 8, 0Ah, 0Bh)
note 1) If you make this call with AL=1 the program will be loaded as if you
made the call with AL=0 except that the program will not be executed.
Additionally, with AL=1 the stack segment and pointer along with the
program's CS:IP entry point are returned to the program which made the
4B01h call. These values are put in the four words at ES:BX+0Eh. On
entry to the call ES:BX points to the environment address, the command
line and the two default FCBs. This form of EXEC is used by DEBUG.COM.
2) Application programs may invoke a secondary copy of the command
processor (normally COMMAND.COM) by using the EXEC function. Your
program may pass a DOS command as a parameter that the secondary
command processor will execute as though it had been entered from the
standard input device.
The procedure is:
A. Assure that adequate free memory (17k for 2.x and 3.0, 23k for 3.1
up) exists to contain the second copy of the command processor and
the command it is to execute. This is accomplished by executing
function call 4Ah to shrink memory allocated to that of your current
requirements. Next, execute function call 48h with BX=0FFFFh. This
returns the amount of memory availible.
B. Build a parameter string for the secondary command processor in the
form:
1 byte length of parameter string
xx bytes parameter string
1 byte 0Dh (carriage return)
For example, the assembly language statement below would build the
string to cause execution of the command FOO.EXE:
DB 19,"/C C:FOO",13
C. Use the EXEC function call (4Bh), function value 0 to cause execution
of the secondary copy of the command processor. (The drive,
directory, and name of the command processor can be gotten from the
COMSPEC variable in the DOS environment passed to you at PSP+2Ch.)
D. Remember to set offset 2 of the EXEC control block to point to the
string built above.
3) All open files of a process are duplicated in the newly created
process after an EXEC, except for files originally opened with the
inheritance bit set to 1.
4) The environment is a copy of the original command processor's
environment. Changes to the EXECed environment are not passed back to
the original. The environment is followed by a copy of the DS:DX
filename passed to the child process. A zero value will cause the
child process to inherit the environment of the calling process. The
segment address of the environment is placed at offset 2Ch of the
PSP of the program being invoked.
5) This function uses the same resident part of COMMAND.COM, but makes a
duplicate of the transient part.
6) How EXEC knows where to return to: Basically the vector for int 22h
holds the terminate address for the current process. When a process
gets started, the previous contents of int 22h get tucked away in the
PSP for that process, then int 22h gets modified. So if Process A
EXECs process B, while Process B is running, the vector for int 22h
holds the address to return to in Process A, while the save location in
Process B's PSP holds the address that process A will return to when
*it* terminates. When Process B terminates by one of the usual legal
means, the contents of int 22h are (surmising) shoved onto the stack,
the old terminate vector contents are copied back to int 22h vector from
Process B's PSP, then a RETF or equivalent is executed to return control
to process A.
7) To load an overlay file with 4B: first, don't de-allocate the memory
that the overlay will load into. With the other 4Bh functions, the
opposite is true--you have to free the memory first, with function 4Ah.
Second, the "segment address where the file will be loaded" (first item
in the parameter block for sub-function 03) should be a paragraph
boundary within your currently-allocated memory. Third, if the
procedures within the overlay are FAR procs (while they execute, CS will
be equal to the segment address of the overlay area), the relocation
factor should be set to zero. On the other hand, if the CS register
will be different from the overlay area's segment address, the
relocation factor should be set to represent the difference. You
determine where in memory the overlay file will load by using the
segment address mentioned above. Overlay files are .EXEs (containing
header, relocation table, and memory image).
8) When function 00h returns, all registers are changed, including the
stack. You must resore SS, SP, and any other required registers.


Function 4Ch Terminate a Process (EXIT)
Quit with ERRORLEVEL exit code
entry AH 4Ch
AL exit code in AL when called, if any, is passed to next process
return none
note 1) Control passes to DOS or calling program
2) return code from AL can be retrieved by ERRORLEVEL or function 4Dh
3) all files opened by this process are closed, buffers are flushed, and
the disk directory is updated
4) Restores Terminate vector from PSP:000Ah
Ctrl-C vector from PSP:000Eh
Critical Error vector from PSP:0012h


Function 4Dh Get Return Code of a Subprocess (WAIT)
Gets return code from functions 31h and 4Dh (ERRORLEVEL)
entry AH 4Dh
return AL exit code of subprogram (functions 31h or 4Ch)
AH circumstance which caused termination
00h normal termination
01h control-break
02h critical device error
03h terminate and stay resident (function 31h)
note The exit code is only returned once


Function 4Eh Find First Matching File (FIND FIRST)
entry AH 4Eh
CX search attributes
DS:DX pointer to ASCIIZ filename (with attributes)
return CF set AX error code (2, 12h)
clear data block written at current DTA
format of block is: (info from BIX)
documented by Micro- |00h 1 byte attribute byte of search
soft as "reserved for |01h 1 byte drive letter for search
DOS' use on subsquent |02h 11 bytes the search name used
Find Next calls" |0Ch 2 bytes word value of last entry
function 4Fh |0Fh 4 bytes dword pointer to this DTA
|13h 2 bytes word directory start
| PC-DOS 3.10 (from INTERRUP.ARC)
|00h 1 byte drive letter
|01h-0Bh bytes search template
|0Ch 1 byte search attributes
| DOS 2.x (and DOS 3.x except 3.1?) (from INTERRUP.ARC)
|00h 1 byte search attributes
|01h 1 byte drive letter
|02h-0Ch bytes search template
|0Dh-0Eh 2 bytes entry count within directory
|0Fh-12h bytes reserved
|13h-14h 2 bytes cluster number of parent directory

15h 1 byte file attribute
16h 2 bytes file time
18h 2 bytes file date
1Ah 2 bytes low word of file size
1Ch 2 bytes high word of file size
1Eh 13 bytes name and extension of file found, plus
1 byte of 0s. All blanks are removed
from the name and extension, and if an
extension is present it is preceded by a
period.
note 1) Will not find volume label
2) This function does not support network operations
3) Wildcards are allowed in the filespec
4) If the attribute is zero, only ordinary files are found. If the volume
label bit is set, only volume labels will be found. Any other attribute
will return that attribute and all normal files together.
5) To look for everything except the volume label, set the hidden, system,
and subdirectory bits all to 1


Function 4Fh Find Next Matching File (FIND NEXT)
Find next ASCIIZ file
entry AH 4Fh
return CF clear data block written at current DTA
set AX error code (2, 12h)
note 1) If file found, DTA is formatted as in call 4Eh
2) Volume label searches using 4Eh/4Fh reportedly aren't 100% reliable
under DOS 2.x. The calls sometime report there's a volume label and
point to a garbage DTA, and if the volume label is the only item they
often won't find it
3) This function does not support network operations
4) Use of this call assumes that the original filespec contained wildcards


Function 50h "Used Internally by DOS" - Set PSP
* Set new Program Segment Prefix (current Process ID)
entry AH 50h
BX segment address of new PSP
return none - swaps PSP's regarded as current by DOS
note 1) By putting the PSP segment value into BX and issuing call 50h DOS stores
that value into a variable and uses that value whenever a file call is
made.
2) Note that in the PSP (or PDB) is a table of 20 (decimal) open file
handles. The table starts at offset 18h into the PSP. If there is an
0FFh in a byte then that handle is not in use. A number in one of the
bytes is an index into an internal FB table for that handle. For
instance the byte at offset 18h is for handle 0, at offset 19h handle
1, etc. up to 13h. If the high bit is set then the file associated by
the handle is not shared by child processes EXEC'd with call 4Bh.
3) Function 50h is dangerous in background operations prior to DOS 3.x as
it uses the wrong stack for saving registers. (same as functions
0..0Ch in DOS 2.x)
4) Under DOS 2.x, this function cannot be invoked inside an int 28h handler
without setting the Critical Error flag
5) Open File information, etc. is stored in the PSP DOS views as current.
If a program (eg. a resident program) creates a need for a second PSP,
then the second PSP should be set as current to make sure DOS closes
that as opposed to the first when the second application finishes.
6) See PC Mag Vol.5, No 9, p.314 for discussion.
7) Used by DOS 3.3 PRINT & DEBUG, DesQview 2.01, Windows 1.03, SYMDEB
from MASM 4.0


Function 51h "Used Internally by DOS" - Get Program Segment Prefix
* Returns the PSP address of currently executing program
entry AH 51h
return BX address of currently executing program
offset
00h program exit point
02h memory size in paragraphs
04h unused (0)
05h CP/M style entry point (far call to DOS)
0Ah terminate address (old int 22h)
0Ch terminate segment
0Eh break address (old int 23h)
10h break segment
12h error address (old int 24h)
14h error segment
16h parent PSP segment
18h DOS 2.0+ open files, 0FFh = unused
2Ch DOS 2.0+ environment segment
2Eh far ptr to process's SS:SP
32h DOS 3.x max open files
34h DOS 3.x openfile table address
36h DOS 3.x openfile table segment
38h unused by DOS versions <= 3.3
50h DOS function dispatcher (FAR routine)
53h unused
55h FCB #1 extension
5Ch FCB #1
6Ch FCB #2
80h command tail / default DTA buffer
note 1) Used in DOS 2.x, 3.x uses 62h
2) Function 51h is dangerous in background operations prior to DOS 3.x as
it uses the wrong stack for saving registers. (same as functions
0..0Ch in DOS 2.x)
3) 50h and 51h might be used if you have more than one process in a PC.
For instance if you have a resident program that needs to open a file
you could first call 51h to save the current id and then call 50h to set
the ID to your PSP.
4) Under DOS 2.x, this function cannot be invoked inside an int 28h handler
without setting the Critical Error flag
5) Used by DOS 3.3 PRINT, DEBUG


Function 52h "Used Internally by DOS" - IN-VARS
* Returns a pointer to a set of DOS data variables MCB chain,
pointer to first device driver and a pointer to disk parameter
blocks (first one)
entry AH 52h
return ES:BX pointer to the DOS list of lists, for disk information. Does not
access the disk, so information in tables might be incorrect if
disk has been changed. Returns a pointer to the following array
of longword pointers:
Bytes Value
-2h,-1h segment of first memory control block
00h-03h pointer to first DOS disk block (see function 36h)
04h-07h Pointer to list of DOS file tables
dword pointer to next file table
word number of files in this table
35h bytes per file
00h-01h number of file handles referring to
this file
02h-06h unknown
07h-0Ah pointer to device driver header if
character device; pointer to DOS Device
Control Block if block device (see
fn 32h for format)
0Bh-1Fh unknown
20h-2Ah filename in FCB format (no path, no
period, blank-padded)
2Bh-2Ch PSP segment of file's owner
2Dh-30h unknown - 0 always
31h-32h unknown
33h-34h unknown
8h-0Bh pointer to CLOCK$ device driver, whether installable or
resident
0Ch-0Fh pointer to actual CON: device driver, whether
installable or resident
(DOS 2.x)
10 number of logical drives in system
11-12 maximum bytes/block of any block device
13-16 unknown
17 beginning (not a pointer. The real beginning!) of NUL
device driver. This is the first device on DOS's linked
list of device drivers.
(DOS 3.x)
10h-11h maximum bytes/block of any block device (0200h)
12h-15h pointer to first disk buffer
16h-19h partially undefined: Pointer to array of drive info:
51h bytes per drive, starting with A: ...
00h-3Fh current path as ASCIIZ, starting with 'x:\'
40h-43h unknown zeros always
44h unknown flags? Usually 40h, except for
entry after last valid entry = 00h
45h-48h pointer to DOS disk block for this drive
49h-4Ah unknown. Current track or block?
-1 if never accessed
4Bh-4Eh unknown -1 always
4Fh-52h unknown 2 always
1Ah-1Dh pointer to FCB table (if CONFIG.SYS contains FCBS=)
1Eh-1Fh size of FCB table
20h number of block devices
21h value of LASTDRIVE command in CONFIG.SYS (default 5)
22h beginning (not a pointer. The real beginning!) of NUL
device driver. This is the first device on DOS's linked
list of device drivers.
note 1) This call is not supported in OS/2 1.0's DOS Compatibility Box
2) Used by DOS 4.0 MEM.EXE, DOS 3.3 ASSIGN.COM, PRINT.COM, SUBST.EXE


Function 53h "Used Internally by DOS" - Translate BPB
* Translates BPB (BIOS Parameter Block, see below) into a DOS Disk
Block (see function call 32h).
entry AH 53h
DS:SI pointer to BPB
ES:BP pointer to area for DOS Disk Block.
Layout of Disk Block:
bytes value
00h-01h bytes per sector, get from DDB bytes 02h-03h.
02h sectors per cluster, get from (DDB byte 4) + 1
03h-04h reserved sectors, get from DDB bytes 06h-07h
05h number of FATs, get from DDB byte 08h
06h-07h number of root dir entries, get from DDB bytes 09h-0Ah
08h-09h total number of sectors, get from:
((DDB bytes 0Dh-0Eh) - 1) * (sectors per cluster (BPB
byte 2)) + (DDB bytes 0Bh-0Ch)
0Ah media descriptor byte, get from DDB byte 16h
0Bh-0Ch number of sectors per FAT, get from DDB byte 0Fh
return unknown


Function 54h Get Verify Setting
Get verify flag status
entry AH 54h
return AL 00h if flag off
01h if flag on
note Flag can be set with function 2Eh


Function 55h "Used Internally by DOS" - Create "Child" PSP
* Create PSP: similar to function 26h (which creates a new Program
Segment Prefix at segment in DX) except creates a "child" PSP
rather than copying the existing one.
entry AH 55h
DX segment number at which to create new PSP.
return unknown
note 1) This call is similar to call 26h which creates a PSP except that unlike
call 26h the segment address of the parent process is obtained from the
current process ID rather than from the CS value on the stack (from the
INT 21h call). DX has the new PSP value and SI contains the value to be
placed into PSP:2 (top of memory).
2) Function 55 is merely a substitute for function 26h. It will copy the
current PSP to the segment address DX with the addition that SI is
assumed to hold the new memory top segment. This means that function
26h sets SI to the segment found in the current PSP and then calls
function 55h.


Function 56h Rename a File
entry AH 56h
DS:DX pointer to ASCIIZ old pathname
ES:DI pointer to ASCIIZ new pathname
return CF clear successful rename
set AX error code (2, 3, 5, 11h)
note 1) Works with files in same drive only
2) Global characters not allowed in filename
3) The name of a file is its full pathname. The file's full pathname can
be changed, while leaving the actual FILENAME.EXT unchanged. Changing
the pathname allows the file to be "moved" from subdirectory to
subdirectory on a logical drive without actually copying the file.
4) DOS 3.x allows renaming of directories



  3 Responses to “Category : Miscellaneous Language Source Code
Archive   : 1216REF.ZIP
Filename : CHAPTER.004

  1. Very nice! Thank you for this wonderful archive. I wonder why I found it only now. Long live the BBS file archives!

  2. This is so awesome! 😀 I’d be cool if you could download an entire archive of this at once, though.

  3. But one thing that puzzles me is the “mtswslnkmcjklsdlsbdmMICROSOFT” string. There is an article about it here. It is definitely worth a read: http://www.os2museum.com/wp/mtswslnk/