Category : System Diagnostics for your computer
Archive   : JUMPERS.ZIP
Filename : Z150

 
Output of file : Z150 contained in archive : JUMPERS.ZIP
** Z-151
-----

CPU BOARD
---------

SW1
---
SECTION DEFINITION
------- ----------
0 DETERMINES WHETHER FLOPPY DISKS ARE
CONNECTED TO THE COMPUTER. IF "OFF", SECTIONS 6 AND
7 DO NOT APPLY

*ON=YES
OFF=NO

1 DETERMINES IF THE COPROCESSOR IS INSTALLED
*ON=COPROCESSOR NOT INSTALLED
OFF=COPROCESSOR INSTALLED

2-3 DETERMINES THE BASE SIZE OF THE MEMORY DEVICES USED
IN THE COMPUTER

ON ON =16K DEVICES
ON OFF =32K DEVICES
OFF ON =48K DEVICES
OFF OFF=64K DEVICES
NOTE: FOR 256K DEVICES NEED ZPAL!

4-5 DETERMINES THE DISPLAY WIDTH
OFF ON =40 CHARACTER LINES
*ON OFF =80 CHARACTER LINES
OFF OFF= SECOND MONOCHROME CARD
ON ON =EGA/VGA

6-7 DETERMINES THE NUMBER OF FLOPPY DRIVES
INSTALLED
*OFF OFF =4
ON OFF =3
OFF ON =2
ON ON =1

SW2
---

SECTION DEFINITION
------- ----------
0,1,2,3,4 DETERMINES THE MEMORY SIZE OF THE COMPUTER

0 1 2 3 4
- - - - -
ON ON ON ON ON 64K
ON OFF ON ON ON 128K
ON ON OFF ON ON 192K
ON OFF OFF ON ON 256K
ON ON ON OFF ON 320K
ON OFF ON OFF ON 384K
ON ON OFF OFF ON 448K
ON OFF OFF OFF ON 512K
ON ON ON ON OFF 576K
ON OFF ON ON OFF 640K

5-6 THESE SWITCH SECTIONS DETERMINE THE DEVICE USED FOR
AUTOBOOT. IF A DEVICE IS NOT SPECIFIED, MANUAL
BOOTING WILL RESULT

OFF ON = AUTOBOOT FROM FLOPPY
ON OFF= AUTOBOOT FROM WINCHESTER

7 DETERMINES THE FREQUENCY OF THE POWER SOURCE
*ON = 60HZ
OFF= 50 HZ

MEMORY CARD
-----------

JUMPER
LOCATION SETTING COMMENTS
-------- ------- --------
J401 *1 CARD ADDRESSED AS THE FIRST BANK OF RAM
(0-320K).

2 CARD ADDRESSED AS SECOND BANK OF RAM
(320-640K)

J402 0 PARALLEL PRINTER PORT ADDRESS 3BC (HEX)

*1 PARALLEL PRINTER PORT ADDRESS 378 (HEX)

J403 *0 PARALLEL PORT ENABLED
1 PARALLEL PORT DISABLED

VIDEO CARD
----------

JUMPER
LOCATION SETTING COMMENTS
-------- ------- --------
J301 *+(POSITIVE) LIGHT PEN PULSE SELECT. NOT
-(NEGATIVE) SUPPORTED

J302/J303 J302 J303 CHARACTER FONT
OFF OFF *DOUBLE-DOT CHARACTERS
ON OFF SINGLE-DOT CHARACTERS
OFF ON UNDERLINED DOUBLE-DOT CHARACTERS
ON ON UNDERLINED SINGLE-DOT CHARACTERS

J304 *C COMPOSITE (HORIZONTAL AND VERTICA)
SYNC
V SEPARATE HORIZONTAL AND VERTICAL SYNC

J305 +(POSITIVE) POSITIVE POLARITY OF VERTICAL SYNC
SIGNAL SENT TO AN INTERNAL MONITOR
*-(NEGATIVE) NEGATIVE POLARITY OF VERTICAL SYNC SIGNAL
SENT TO AN INTERNAL MONITOR

J306 *+(POSITIVE) POSITIVE POLARITY OF HORIZONTAL SYNC
SIGNAL SENT TO RGB CONNECTOR
-(NEGATIVE) NEGATIVE POLARITY OF HORIZONTAL SYNC
SIGNAL SENT TO RGB CONNECTOR

J307 *+(POSITIVE) POSITIVE POLARITY OF VERTICAL-COMPOSITE
SYNC SIGNAL SENT TO RGB CONNECTOR
-(NEGATIVE) NEGATIVE POLARITY OF VERTICAL-
COMPOSITE SYNC SIGNAL SENT TO RGB
CONNECTOR

TO DISABLE VIDEO, THE VIDEO DISABLE PAL KIT IS REQUIRED

** Z-151, Z-152, Z-158, and Z-160 Switch Settings
----------------------------------------------

CPU CARD
---------
THE CPU CARD IS THE SAME IN THE 151, 152 AND 160
SEE THE SWITCH SETTINGS SECTION FOR THE MODEL 151


VIDEO/FLOPPY CARD
-----------------

THIS CARD IS USED ONLY IN THE 152 AND 158 COMPUTERS

85-3012-11

JUMPER
LOCATION SETTING COMMENTS
-------- ------- --------
J301 SELECTS POLARITY OF THE LIGHT PEN PULSE, WHICH
IS NOT SUPPORTED

2-3 POSITIVE PULSE
1-2 NEGATIVE PULSE

J302 SELECTS A COMPOSITE (HORIZONTAL AND VERTICAL)
SYNC SIGNAL OR A PURE VERTICAL SYNC SIGNAL TO AN
EXTERNAL MONITOR

2-3 COMPOSITE SYNC SIGNAL
1-2 VERTICAL SYNC SIGNAL

J303 SELECTS THE POLARITY OF THE VERTICAL SYNC SIGNAL
SENT TO AN EXTERNAL MONITOR

2-3 NEGATIVE
1-2 POSITIVE

J304 SELECTS THE POLARITY OF THE VERTICAL SYNC SIGNAL
SENT TO AN INTERNAL MONITOR

2-3 NEGATIVE
1-2 POSITIVE

J305 SELECTS THE POLARITY OF THE HORIZONTALSYNC
SIGNAL SENT TO AN EXTERNAL MONITOR

2-3 NEGATIVE
1-2 POSITIVE

J306 SELECTS THE POLARITY OF THE HORIZONTAL SYNC
SIGNAL SENT TO AN INTERNAL MONITOR

2-3 NEGATIVE
1-2 POSITIVE


JUMPER INTERRUPT VECTOR
J307 IRQ2
J308 IRQ3 (COM2)
J309 IRQ4 (COM1)
J310 IRQ5
J311 IRQ6
J312 IRQ7

NOTE: ONLY ONE JUMPER MAY BE INSTALLED ON THIS SECTION.
NORMALLY, J308 (COM2) OR J309 (COM1) IS JUMPERED


SWITCH 301 SETTINGS

SECTION DEFINITION
1 USED TO SELECT THE CHARACTER CODE. SETTINGS ARE AS
FOLLOWS:
ON=CUSTOM
*OFF=STANDARD

2 USED TO SELECT A SERIAL PORT
*ON=COM1 (IRQ4)
OFF=COM2 (IRQ3)

3 USED TO ENABLE OR DISABLE THE SELECTED SERIAL PORT
*ON=SERIAL PORT ENABLED
OFF=SERIAL PORT DISABLED

4 USED TO ENABLE OR DISABLE THE VIDEO CIRCUITRY
*ON=VIDEO ENABLED
OFF=VIDEO DISABLED

** Z-157 SWITCH SETTINGS
---------------------

PARENT BOARD

SW101

SWITCH
SECTION FUNCTION SETTING

0,1 SYSTEM BOOT UP
MANAUL BOOT OFF OFF
OR
ON ON
AUTOBOOT HDD ON OFF
AUTOBOOT FDD OFF ON

2 MEMORY PARITY
ENABLED *ON
DISABLED OFF

3 MEMORY LOCATION (REFERS TO SYSTEM MEMORY, NOT EMS)
(OVER 256K)
PARENT BOARD *ON
EXPANSION CARD OFF

4,5 VIDEO INTERFACE
MDA *OFF OFF
CGA (80 COLUMNS) ON OFF
RESERVED OFF ON
EGA ON ON

6 PARALLEL PORT
ENABLED *ON
DISABLED OFF

7 FLOPPY DISK
CONTROLLER
ENABLED *ON
DISABLED OFF

VIDEO CARD
----------

THERE IS ONLY ONE SWITCH ON THIS CARD, SET FOR EITHER
COLOR OR MONOCHROME

** Z-158 SWITCH SETTINGS
---------------------

CPU/MEMORY CARD
---------------

THERE ARE 3 DIFFERENT VERSIONS OF THE CPU/MEMORY BOARD. THE
JUMPER SETTINGS CHANGE DEPENDING ON WHICH VERSION OF THE
BOARD IS BEING USED. HOWEVER, THE SWITCH SETTINGS ARE THE
SAME.

SECTION DEFINITION
1 POWER SUPPLY FREQUENCY
*ON=60 HZ
OFF=50 HZ

2 AUTOBOOT
*ON=FDD
OFF=HDD

3 FLOPPY DISK CONTROLLER CIRCUITRY
*ON=ENABLED
OFF=DISABLED

4 COLOR OR MONOCHROME CIRCUITRY
ON=COLOR
*OFF=MONOCHROME

JUMPERS
-------

CIRCUIT BOARD 85-3118-XX
------------------------

JUMPER DEFINITION CONFIGURATION/COMMENTS
DESIGNATION
----------- ---------- ----------------------
J201 X RAM ENABLED HARD WIRED IN WITH FOIL TRACE

J202,J203 MEMORY DEVICE
TYPE AND # OF
BANKS

J202 J203
IN IN =ONLY 64K DEVICES CAN BE USED
IN OUT =BANK 0 CONTAINS 256K DEVICES
OUT IN =BANKS 0 AND 1 CONTAIN 256K DEVICES AND BANK
2 IS EMPTY
OUT OUT =ALL THREE BANKS CONTAIN 256K DEVICES

IN SOME LATER VERSIONS OF THIS BOARD, J203 IS NOT JUMPERABLE
AND IS EQUIVALENT TO THE "OUT" CONDITION. IN THIS CASE, J202
IS CONFIGURED AS FOLLOWS:


BANK 0 MUST ALWAYS HAVE 256K DEVICES- ADDITIONALLY FOR BANKS
1 AND 2

J203 IN FOR THE FOLLOWING CASES:
-------------------------------
BANKS 1 AND 2 ARE EMPTY OR
BANK 1 HAS 64K DEVICES WITH BANK 2 EMPTY OR
BANKS 1 AND 2 BOTH HAVE 64K DEVICES

J203 OUT FOR THE FOLLOWING CASES:
---------------------------------
BANK 1 HAS 256K DEVICES WITH BANK 2 EMPTY
OR
BANKS 1,2 BOTH HAVE 256K DEVICES

------------------------------------------------------------
J204 PARALLEL PORT 1-2 IN FOR LPT1 (CLOSEST TO
SELECT TOP EDGE OF THE BOARD)
2-3 IN FOR LPT2 (CLOSEST TO
BOTTOM EDGE OF THE BOARD

J206 KEYBOARD FILTER ALWAYS OUT


CIRCUIT BOARDS 85-3162-XX AND 85-3200-XX
----------------------------------------

JUMPER DEFINITION CONFIGURATION/COMMENTS
DESIGNATION
----------- ---------- ----------------------
J201 X RAM ENABLED HARD WIRED IN WITH FOIL TRACE

J202 GATE ARRAY/ *1-2 FOR GATE ARRAY (CLOSEST TO
STANDARD CELL DRAM BANKS)
2-3 IN FOR STANDARD CELL
(FURTHEST AWAY FROM DRAM BANKS)

J203 GATE ARRAY/ IN FOR STANDARD CELL
STANDARD CELL *OUT FOR GATE ARRAY

J/P204 KEYBOARD POSITION 1, 2, 3
CONNECTOR *OUT-NO JUMPER INSTALLED

J205 GATE ARRAY/ IN FOR STANDARD CELL
STANDARD CELL *OUT FOR GATE ARRAY

J206 MEMORY DEVICE
TYPE /# OF BANKS

BANK 0 MUST ALWAYS HAVE 256K DEVICES- ADDITIONALLY FOR BANKS
1 AND 2

J206 IN FOR THE FOLLOWING CASES:
-------------------------------
BANKS 1 AND 2 ARE EMPTY OR
BANK 1 HAS 64K DEVICES WITH BANK 2 EMPTY OR
BANKS 1 AND 2 BOTH HAVE 64K DEVICES

J206 OUT FOR THE FOLLOWING CASES:
---------------------------------
BANK 1 HAS 256K DEVICES WITH BANK 2 EMPTY
OR
BANKS 1,2 BOTH HAVE 256K DEVICES

EACH BANK MUST CONTAIN ONLY ONE TYPE OF DRAM DEVICE; EITHER
256K OR 64K DEVICES, AND MUST BE COMPLETELY FILLED BEFORE
DEVICES ARE INSTALLED IN THE NEXT BANK

IF 256K DEVICES ARE USED WITH 64K DEVICES, THEY MUST BE
INSTALLED IN THE LOWER MOST BANK IE-BANK 0

JUMPER DEFINITION CONFIGURATION/COMMENTS
DESIGNATION
----------- ---------- ----------------------
J207 NOT SCREENED

J208 PARALLEL PORT *1-2 FOR LPT1 (CLOSEST TO
SELECT TOP EDGE OF THE BOARD)
2-3 FOR LPT2 (CLOSEST TO
BOTTOM EDGE OF THE BOARD

J209 PARALLEL PORT *IN FOR ENABLE
ENABLE OUT FOR DISABLE

J210 GATE ARRAY/ 1-2 FOR STANDARD CELL (CLOSEST
STANDARD CELL TOP EDGE OF THE BOARD)
*2-3 FOR GATE ARRAY (CLOSEST TO
BOTTOM EDGE OF THE BOARD

J211- ONLY PRESENT ON 85-3200-XX BOARDS (NOT 85-3162-XX)

J211 PARALLEL PORT *1-2 LPT1, IRQ7 (CLOSEST TO
INTERRUPT REQUEST TOP EDGE OF THE BOARD
2-3 LPT2, IRQ5 (CLOSEST TO
BOTTOM EDGE OF THE BOARD

** Z-159 SWITCH SETTINGS
---------------------

CPU (PN 181-6836)

SWITCH 101 * -DEFAULT SWITCH SETTIMGS WHERE
APPLICABLE
SWITCH
SECTION(S) FUNCTION SETTINGS
0 FLOPPY DISK DRIVES INSTALLED
ONE OR MORE OFF
NONE ON

1 8087 NUMERIC COPROCESSOR
INSTALLED OFF
NOT INSTALLED ON

2 8 MHZ MEMORY SPEED (512K TO 640K)
3 WAIT STATES OFF
0 WAIT STATES ON

3 MONITOR ROM, SCRATCHPAD RAM
WRITE PROTECTED *OFF
UNPROTECTED ON

4 5 INITIAL VIDEO MODE, CHARACTERS
PER LINE
EGA OR OPTIONAL CONTROLLER ON ON
40 x 25 TEXT, CGA OFF ON
80 x 25 TEXT, CGA ON OFF
80 x 25 MONOCHROME OFF OFF

6 7 NUMBER OF FLOPPY DRIVES
1 DRIVE ON ON
2 DRIVES OFF ON
3 DRIVES ON OFF
4 DRIVES OFF OFF


SWITCH 102

FUNCTION CONFIGURATION SWITCH POSITION AND SETTING

0 1 2 3 4 5 6 7
SYSTEM MEMORY 256K ON OFF OFF ON ON
SIZE 512K ON OFF OFF OFF ON
640K ON OFF ON ON OFF

AUTOBOOT NO AUTOBOOT ON ON
FLOPPY DRIVE OFF ON
WINCHESTER ON OFF
RESERVED OFF OFF

DISPLAY 60 HZ ON
FREQUENCY 50 HZ OFF


SYSTEM MEMORY/PARALLEL PORT CARD SWITCH SETTINGS [PN
181-7575 (512K)]

SWITCH 401

SWITCH
SECTION(S) FUNCTION SETTINGS

SETTINGS
1 TYPE OF RAM ON MEMORY CARD
SYSTEM/EMS RAM OFF
EMS RAM ONLY ON

2 AMOUNT OF SYSTEM RAM
MAXIMUM 640K OFF
MAXIMUM 512K ON

3 EMS RAM ENABLE
ENABLED OFF
DISABLED ON

4 EMS FRAME ADDRESS
D0000 TO DFFFF OFF
E0000 TO EFFFF ON

5,6 EMS MEMORY CARD I/O PORT SELECT
EMS CARD 0 ON ON
EMS CARD 1 ON OFF
EMS CARD 2 OFF ON
EMS CARD 3 OFF OFF

7 PRINTER INTERRUPT REQUEST SIGNAL
(IRQ7) BUS CONNECT/DISCONNECT
NO INTERRUPT OFF
INTERRUPT DRIVEN *ON

8,9 PARALLEL PRINTER ADDRESS SELECT
PORT 278-27A ON ON
PORT 3BC-3BE ON OFF LPT2
PORT 378-37A OFF ON LPT1
DISABLED OFF OFF

10 EMS LOGIC INSTALLED/NOT
INSTALLED ON MEMORY CARD
DIP JUMPER AT U455 OFF
EMS PAL IC AT U455 ON


FLOPPY ONLY DISK CONTROLLER (PN 181-7262)
U601
SWITCH
SECTION
FUNCTION SETTINGS
1 SERIAL PORT ENABLE/DISABLE
ENABLE *ON
DISABLE OFF

2 SERIAL PORT RESIDENCE
PRIMARY (COM1) *ON
SECONDARY (COM2) OFF

3 TYPE OF CABLE
STRAIGHT *ON PC/XT
TWISTED OFF

4 PRECOMPENSATION TIMING
TRACKS 44 TO 80 ON
ALL TRACKS *OFF


HERCULES VIDEO /FLOPPY DISK CONTROLLER CARD
MODELS 1,2 AND 3 PN 181-6893

SWITCH
SECTION(S) FUNCTION SETTINGS

VIDEO CIRCUITRY

3,4 VIDEO OPERATION
ENABLE *ON ON
DISABLE OFF OFF


8 HORIZONTAL SYNC POLARITY
INVERTED(-) ON
NORMAL(+) *OFF

9 VERTICAL SYNC POLARITY
INVERTED(-) ON
NORMAL(+) *OFF

10 MONITOR TYPE
RESERVED ON
ALL MODES *OFF


FLOPPY CIRCUITRY

1 SERIAL PORT RESIDENCE
COM1 *ON
COM2 OFF

2 SERIAL PORT ENABLE/DISABLE
ENABLE *ON
DISABLE OFF

5 TYPE OF CABLE
TWISTED ON
STRAIGHT *OFF PC/XT

6 FLOPPY ENABLE/DISABLE
ENABLE *ON
DISABLE OFF

7 TRACK PRECOMPENSATION
44-80 ON
ALL *OFF


  3 Responses to “Category : System Diagnostics for your computer
Archive   : JUMPERS.ZIP
Filename : Z150

  1. Very nice! Thank you for this wonderful archive. I wonder why I found it only now. Long live the BBS file archives!

  2. This is so awesome! 😀 I’d be cool if you could download an entire archive of this at once, though.

  3. But one thing that puzzles me is the “mtswslnkmcjklsdlsbdmMICROSOFT” string. There is an article about it here. It is definitely worth a read: http://www.os2museum.com/wp/mtswslnk/